Huaqi Zhengbang ZB4050LS Скачать руководство пользователя страница 2

Страница: 2 / 45

WenZhou ZhengBang Electronic Equipment Co., Ltd

ZB4050LS Rev 1.1

Introduction

Thank you for using this product. This operation manual provides the parameters, operation guidance and other related information of

ZB4050LS/ZB4050LY chip mounter.

！

Attention:

1. It is strictly prohibited to copy part of or the entire book (including software and programs) without authorization.

2. The contents of this book can be modified without prior notice.

3. We strive to be accurate in the preparation of the contents of this book. If you find a mistake, omission or suspicious part, please

contact the dealer or the company.

4. The company is not responsible for the results of the error operation, whether it is related to the item (3) or not. Please understand.

！

Attention

：

For safe use of the machine!

The operator of the chip mounter (hereinafter referred to as the machine), maintenance personnel and repair personnel shall carefully

read the following safety precautions before using the machine, so as not to get hurt.

1. Basic precautions

(1) The operation of the machine is only limited to the operator who has mastered the operation of the machine.

(2) Please do not use this machine for other purposes. Otherwise, the company is not responsible for the resulting responsibility.

(3) Do not modify the machine. The company is not responsible for the accident caused after unauthorized modification.

(4) In order to prevent accident caused by unexpected start-up, please cut off the power supply before carrying out the maintenance,

repair and cleaning.

(5) When unplugging the power plug, please hold the plug body instead of the wire and pull out.

2. Precautions for application

(1) Please take the necessary safety actions during transportation to prevent inversion or falling.

(2) Please take care of the equipment for shipment.

(3) Please put the machine in a stable place for installation.

(4) In order to prevent personal accident, before switching on the power supply, please confirm that the cable is not damaged, shedding,

loose, etc.

(5) In order to prevent personal accident, before switching on the power supply, please confirm that the machine is safely grounded.

(6) In order to prevent accidents caused by unskilled operation, the repair and commissioning work shall be carried out by skilled

technicians. When changing the components, please use the company's genuine parts. The company is not responsible for the accident

caused by the use of non-genuine parts.

(7) In order to prevent the electric shock caused by unskilled operation, electrical repairing shall be entrusted to the professional staff.

(8) In order to prevent human injury, after repair, adjustment or spare parts replacement, please confirm that the screws and nuts are

not loose.

3. Precautions for working environment

(1) Do not use the machine under the environment of high frequency welding machine and other noise sources (electromagnetic wave).

(2) Do not use the machine when the power voltage exceeds 10% of the rated voltage.

(3) When it thunders, stop using the machine and cut off the power.

Содержание ZB4050LS














































Результаты поиска

Содержание ZB4050LS

Отзывы:

Похожие инструкции для ZB4050LS

Бренды по названию

Популярные бренды

Huaqi Zhengbang ZB4050LS, Руководство пользователя

Результаты поиска

Содержание ZB4050LS

Отзывы:

Похожие инструкции для ZB4050LS

Бренды по названию

Популярные бренды