HTO HTO-100, Руководство пользователя, Страница: 4 / 36

4
B
A
Specifications HTO-100 HTO-150 HTO-200 HTO-250 HTO-300
Salt Used - Per Regeneration 6.0 lbs 9.0 lbs 12.0 lbs 15.0 lbs 18.0 lbs
Water Used - Regeneration 86.4 gal 148 gal 162.4 gal 216.0 gal 224.8 gal
Hardness Removal - Grains 25,000 37,500 50,000 67,500 75,000
Tank #1 Carbon Quantity (ft3) 1.0 ft 1.50 ft 2.0 ft 2.5 ft 3.0 ft
Tank #2 Resin Quantity (ft3) 1.0 ft 1.50 ft 2.0 ft 2.5 ft 3.0 ft
Tank Size 9x48 10x54 12x52 13x54 14x65
Tank Jacket / Media Loaded Yes Yes No No No
Brine Tank (Inches)
BTR 18.1 x 34.5
BTS 15.0²x34.7
BTR 18.1 x 34.5
BTS 15.0²x34.7
20.3 x 37.4 20.3 x 37.4 23.0 x 40.5
Salt Storage Capacity
BTS 240 lbs BTR
270 lbs
BTS 240 lbs BTR
270 lbs 350 lbs 350 lbs 420 lbs
Flow Rate @ 15 psi Pressure Drop 7.2 gpm 7.4 gpm 9.0 gpm 9.2 gpm 9.2 gpm
Flow Rate @ 25 psi Pressure Drop 10.0 gpm 10.1 gpm 11.9 gpm 12.1 gpm 12.1 gpm
Back Wash Flow Rate 4.0 gpm 5.0 gpm 7.0 gpm 8.0 gpm 10.0 gpm
Shipping Weight 154 lbs 171 lbs 214 lbs 225 lbs 232 lbs
Regeneration Type Up Flow
Plumbing Connections 89 Model 1” Straight NPT. 785 Model 3/4” 90 0 Elbows & 1” Straight NPT
Resin Type Aquafine 8% cation exchange resin
Carbon Type Catalytic Carbon
Electrical Requirements Input 120V 60 Hz - Output 12V 650mA
Water Temperature 40°F and 110°F (4°C - 43°C)
Water Pressure Min. 30 - Max. 125 psi
SPECIFICATION
Working Temperature:
This unit must be
operated at temperatures between 40°F and
110°F (4°C - 43°C).
Working Pressure:
This water softener
must be operated on pressures
between 30 psi to 125 psi. If the water
pressure is higher than 125 PSI, use a
pressure reducing valve in the water supply
line to the softener.
Voltage = 120V / 60 Hz
Pipe Size = 3/4” and 1”
• At the stated service flow rates, the
pressure drop through these devices will
not exceed 15 psig.
• The manufacturer reserves the right
to make product improvements which
may deviate from the specifications
and descriptions stated herein, without
obligation to change previously
manufactured products or to note the
change.
* Do not use water that is microbiologically
unsafe without adequate disinfection
before or after the system.
Peak flow rates intended for intermittent
use only (10 minutes or less) and are for
residential applications only. Do not use
peak flow rate for commercial applications
or for a continuous rate when treated
water supplies are geothermal heat pump,
swimming pool, etc.
For satisfactory operation, the pumping rate
of the well system must equal or exceed
indicated backwash flow rate.
All units come with plastic bypass
Maximum Iron
= 1.5 ppm
Maximum Hydrogen Sulfide
= 0.0 ppm
Maximum Manganese
= .75 ppm
pH
= 6.5 to 8.5
Models A (Inches) B (Inches)
HTO-100
58 9
HTO-150
64 10
HTO-200
62 12
HTO-250
64 13
HTO-300
75 14
SYSTEM DIMENSIONS
All units are factory programmed to the below specifications. Alteration should only be done by a factory trained technician or after consultation with one of our technical
representatives if you have any questions please call 877-288-9888 .