HST HP101 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 17

HST HP101 Скачать руководство пользователя страница 7

damaged when subjected to lightning induced transients. Although no system is
completely immune from lightning transients and interferences, proper grounding will
reduce susceptibility. Overhead or out-side aerial wiring is not recommended, due to
an increased susceptibility to nearby lightning strikes. Consult with the Technical
Services Department if any problems are anticipated or encountered.

Disconnect AC power and batteries prior to removing or inserting circuit boards.
Failure to do so can damage circuits.

Remove all electronic assemblies prior to any drilling, filing, reaming, or punching of
the enclosure. When possible, make all cable entries from the sides or rear. Before
making modifications, verify that they will not interfere with battery, transformer, and
printed circuit board location.

Do not tighten screw terminals more than 9 in-lbs. Over-tightening may damage
threads, resulting in reduced terminal contact pressure and difficulty with screw
terminal removal.

This system contains static-sensitive components. Always ground yourself with a
proper wrist strap before handling any circuits so that static charges are removed from
the body. Use static-suppressive packaging to protect electronic assemblies removed
from the unit.

Follow the instructions in the installation, operating, and programming manuals.
These instructions must be followed to avoid damage to the control panel and
associated equipment. FACP operation and reliability depend upon proper installation
by authorized personnel.

2.Control Panel Installation

2.1 Important Notice

This product should be installed, commissioned and maintained by suitably qualified
service personnel with reference to IEE regulations and any statutory requirements,
for use in fire alarm signaling systems, only when installed in accordance with this
manual and the latest National Fire Protection Association Standards NFPA 72; the
National Electrical Code (NFPA 70); the Life Safety Code (NFPA 101); and/or the
local authority having jurisdiction (AHJ). It is possible to apply system components
incorrectly or arrange system components and installation wiring so that required life
safety functions are NOT performed. As a result, lives may be lost.
To minimize this possibility:



DO NOT deviate from any installation instructions contained in this manual.



DO NOT assume any installation details not shown in this manual.

- 7 -

«
...
5
6
7
8
9
...
»

Содержание HP101


















Отзывы:

Нет отзывов