HST HP101 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 17

HST HP101 Скачать руководство пользователя страница 3

1. Introduction

The fire alarm control panels (4 Zones, 8 Zones, and 16 Zones) provide all of the
sophisticated features required of a leading edge conventional fire alarm system along
with the simple operation and efficient installation methods demanded by both
installers and building users.
The panel can be flush or surface mounted and the generously sized metal back box
allows ample space for rear or top cable entries.
A comprehensive range of auxiliary devices is available to operate with the fire
control panels including optical, ionization, photoelectric, photoelectric-thermal and
heat detectors.
Each of the system components has been specifically designed to operate as part of
the system. This provides assurance that the control panel, smoke detectors, interface
devices and the ancillary components are all fully compatible with one another and
that the full range of system functionality is supported by each device.

1.1 Product Features

The panels have the following key features:



4, 8, or 16 conventional input zones.



2 notification appliance circuits (NAC, Sounder) with built-in

synchronization for ANSI 3.41and Gentex.



The panel comes with a 3 amp power supply.



Dedicated alarm and trouble relays.



1 RS485 can be able to connect repeaters.



Housed in a 383mm W x 295mm H x 87mm D metal enclosure.



Enclosure supports two 12V, 7Ah backup batteries.

1.2 Electrical Specifications

Primary AC

120VAC 50/60 Hz Power supply rating
240VAC 50/60 Hz

Power supply rating

3 Amps @ 24VDC

Maximum Battery Charging Current

0.98 Amps @ 26VDC

Initiating Device Circuits 4 Zones

Alarm Zone 1, 2, 3, & 4

Initiating Device Circuits 8 Zones

Alarm Zone 1, 2, 3, 4, 5, 6, 7, & 8

Initiating Device Circuits 16 Zones

Alarm Zone 1, 2, 3, 4, 5, 6, 7, 8,9,10,11,12,13,14,15, &16

Normal Initiating Operating Voltage

23VDC, Maximum 26VDC, regulated

Short Circuit Initiating Current (per zone)

35mA Maximum

Maximum Initiating Resistance (per zone)

10 ohms

Initiating End-of-Line Resistor

4K7 ohms, 1/2W 5%

Standby Detector Current (per zone)

4mA maximum

Maximum Detector Count (per zone)

30 detectors

Initiating Cabling Type

18AWG Twisted Shielded pair (14 – 18 AWG)

Detector Base Impedance

430 ohms

- 3 -

«
1
2
3
4
5
...
»

Содержание HP101


















Отзывы:

Нет отзывов