manualshive.com logo in svg

HS-Technik PowerRiv HST-PR, Руководство пользователя

Поделиться
Скачать
HS-Technik PowerRiv HST-PR Скачать руководство пользователя страница 7

- 7 -

- 7 -

2.4. Electrical hazards

Work on this tool is to be performed only by a qualified electrician.

Inspect the tool's electrical components on a regular basis. 

Repair loose connections and damaged cables immediately.

Remove the battery before performing repairs on the tool.

The tool must always be kept locked away securely. 

Only authorized persons are allowed access to the tool.

2.4.1 Basic safety measures

2.4.1.1 Workplace safety

a)  Keep your working area clean and well-lighted.  

  A cluttered or poorly illuminated working area may result in accidents.

b) 

Do not operate the tool in areas in which explosions can occur,  

 where

 flammable liquids, gases or dust are located. Power tools produce sparks that 

 

  can ignite dust or vapors. 

c) Pay attention to environmental conditions.

 

  Do not expose tools to rain. 

  Do not use tools in a damp or wet environment. 
d) Keep children and other persons away when using the tool. 

  Distractions may cause you to lose control over the tool.

2.4.1.2. Electrical safety
a) 

Avoid contact with grounded surfaces such as pipes, heaters, stoves

 and  

 refrigerators. 

 

When your body is grounded, there is an increased risk of electrical shock.

b)  Keep the tool away from rain and humidity. 

 

 

The penetration of water into a tool increases the risk of electrical shock.

c)  Keep the tool away from heat, oil, sharp edges or moving parts.

!

The terms "tool" and "power tool" used in the safety information refer to tools powered 

from a wall outlet (with power cord) and battery-powered tools (without a power 

cord).

Im Martelacker 12 – D-79588 Efringen-Kirchen – Phone 0 76 28 - 91 11- 0 – Fax 0 76 28 - 91 11-90

E-Mail: [email protected] – Web: www.hs-technik.com

Содержание PowerRiv HST-PR
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды