HPE OfficeConnect 1850 Series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 97

background image

Ping Test

83

Ping Test

Use the Ping page to send one or more ping requests from the switch to a specified IP address. You
can use the ping request to check whether the switch can communicate with a particular host on an IP
network. A ping request is an Internet Control Message Protocol (ICMP) echo request packet. The
information you enter on this page is not saved as part of the device configuration.
To display the Ping page, click

Diagnostics

>

Ping Test

in the navigation pane.

Figure 54. Ping Page

Table 44. Ping Fields

Click

Start

to ping the specified host and

Stop

to end a ping in progress. If you do not click

Stop

, the

pings continue until the number of pings specified in the Count field has been reached—even if you
navigate way from the Ping page.

Field

Description

IP Address

Specify the IP address you want to reach.

Count

Specify the number of packets to send. The range is 1 to 15 packets and the default is 3 packets.

Interval

Specify the delay between ping packets. The range is from 1 to 60 seconds, and the default is 3 seconds.

Size

Specify the size of the ping packet to be sent. Changing the size allows you to troubleshoot connectivity

issues with a variety of packet sizes, such as large or very large packets. The range is from 0 to 13000

bytes, and the default is 0 bytes.

Status

The current status of the ping test, which can be one of the following:



Not Started—The ping test has not been initiated since viewing the page.



In Progress—The ping test has been initiated and is running.



Stopped—The ping test was interrupted because the user clicked the Stop button.



Done—The test has completed, and information about the test is displayed in the Results area.

Results

The results of the ping test, which includes the following information:



The IP address of the device that was pinged.



The Internet Control Message Protocol (ICMP) number of the packet, starting from 0.



The time it took to receive a reply, in microseconds.



The number of ping packets sent and received, the percent of packets that were lost, and the mini-

mum, average, and maximum round-trip time for the responses in milliseconds.

«
...
81
82
83
84
85
...
»

Содержание OfficeConnect 1850 Series


































































































Отзывы:

Нет отзывов

Похожие инструкции для OfficeConnect 1850 Series

Бренд: Eaton Страницы: 40

Бренд: Edge-Core Страницы: 9

Бренд: Dexon Страницы: 31

Бренд: Accton Technology Страницы: 10

Бренд: Lancom Страницы: 23

SIL IntelliPoint RF S*R*L Series

Бренд: Ametek Страницы: 93

Бренд: Extron electronics Страницы: 3

Бренд: Accton Technology Страницы: 7

Бренд: Ruby Tech Страницы: 254

SI1P-SH-DVI-UCAC

Бренд: Black Box Страницы: 16

Бренд: Cumberland Страницы: 2

Бренд: ICCN Страницы: 48

Бренд: UNIARCH Страницы: 6

Бренд: Alps Electric Страницы: 4

Бренд: Linksys Страницы: 110

Бренд: Emos Страницы: 44

DHS-LIT-SWP-DHS

Бренд: Digital Home System Страницы: 2

Бренд: EMP-Centauri Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды