HPE Cloudline CL2100 Gen10 Скачать руководство пользователя страница 60

Страница: 60 / 60

Action



To determine if the server is supported, check BIOS or BMC Firmware release note and confirm the
server model.

5-6

Server does not boot

Symptom



The server does not boot.

Cause



The system BIOS or BMC Firmware flash process fails.



The system ROM corrupted.



The server boot failed due to updating the BIOS or BMC firmware failed, either through tool or webUI.



A logical drive is not configured on the RAID controller.



The controller boot order is not set properly.



RAID containing multiple logical drives might require the boot logical drive to be selected under Option
ROM.

Action



For BIOS flash process fail cause server does not boot, try to use BMC WebUI to update BIOS again.



BIOS Recovery process.



For BMC Firmware process fail cause server doesn’t boot, contact for repairing process.



A logical drive is not configured on the RAID controller. Configure logical drive on RAID controller and
set controller boot order properly.



Properly select boot logical drive under Option ROM when RAID containing multiple logical drives.

Содержание Cloudline CL2100 Gen10





























































Результаты поиска

Содержание Cloudline CL2100 Gen10

Отзывы:

Похожие инструкции для Cloudline CL2100 Gen10

Бренды по названию

Популярные бренды

HPE Cloudline CL2100 Gen10, Руководство по устранению неисправностей

Результаты поиска

Содержание Cloudline CL2100 Gen10

Отзывы:

Похожие инструкции для Cloudline CL2100 Gen10

Бренды по названию

Популярные бренды