HPE Cloudline CL2100 Gen10 Скачать руководство пользователя страница 35

Страница: 35 / 60



NIC issues flowchart (2 of 2)

From NIC

Issues

Contact
support

Does the

NIC load in

the OS

Enabled the driver

Does

condition still

exist?

Install/reinstall the

driver

Does

condition still

exist?

Eliminate a

firmware/driver mismatch

Does

condition still

exist?

Install

Firmware/driver update

Does

condition still

exist?

Yes

End

Yes

Does the

NIC appear at

POST and are there NIC

POST error Message

Or IPMI event log

Messages?

Reseat the NIC and verify

Cabling is connected properly.

Does

condition still

exist?

Verify that all SFP, Cables, connectors,

are operating properly. Replace

components that are damaged.

Does

condition still

exist?

Verify that no hardware

Compatibility issues exist. Make

necessary changes to

correct issues.

Does

condition still

exist?

Yes

Replace the NIC.

Does

condition still

exist?

End

Update to a supported NIC

firmware/driver set.

Does

condition still

exist?

Eliminate NIC and VC or switch

port configuration mismatches.

Does

condition still

exist?

Enabled the NIC in the

BIOS.

Does

condition still

exist?

Verify that the server does not

require a BIOS update to see the

NIC

Yes

Содержание Cloudline CL2100 Gen10





























































Результаты поиска

Содержание Cloudline CL2100 Gen10

Отзывы:

Похожие инструкции для Cloudline CL2100 Gen10

Бренды по названию

Популярные бренды

HPE Cloudline CL2100 Gen10, Руководство по устранению неисправностей

Результаты поиска

Содержание Cloudline CL2100 Gen10

Отзывы:

Похожие инструкции для Cloudline CL2100 Gen10

Бренды по названию

Популярные бренды