HP StorageWorks A7298A Скачать руководство пользователя страница 19

Страница: 19 / 82

host bus adapter for Windows and Linux installation guide

2–1

Installation

Installation Overview

This chapter provides step-by-step instructions for installing the HP StorageWorks
A7298A Host Bus Adapter (HBA) including:

•

Hardware Requirements

•

Recording Reference Numbers

•

Installing the HBA into a Computer

•

Verifying the Installation

•

Configuration Guidelines

This chapter also provides information on installation guidelines and supported
configurations for the operating systems.

IMPORTANT: The HBA contains static-sensitive components. Comply with Electrostatic
Discharge (ESD) procedures.

Hardware Requirements

The system hardware requirements for installing the HBA include:

•

A host computer that provides 3.3VDC PCI and PCI-X bus power

•

One open 64-bit 33/66 MHz PCI or 66/100/133 MHz PCI-X bus slot with either a
3.3 or a 5.0 VDC signaling interface

•

Multimode fiber optic cable with LC connector, used with short-wave lasers

Содержание StorageWorks A7298A



















































































Результаты поиска

Содержание StorageWorks A7298A

Отзывы:

Похожие инструкции для StorageWorks A7298A

Бренды по названию

Популярные бренды

HP StorageWorks A7298A, Руководство пользователя

Результаты поиска

Содержание StorageWorks A7298A

Отзывы:

Похожие инструкции для StorageWorks A7298A

Бренды по названию

Популярные бренды