HP ProLiant DL380e Скачать руководство пользователя | Manualshive

Страница: 42 / 155

background image

RBSU menu (HP ProLiant G7 servers or server blades) 42

The Fast setting is optimal for most workloads that require a low latency response to an increase in
processor demand. The slow setting is optimal for some workloads where a longer latency response to

increases in processing demand is an acceptable tradeoff for reduced power consumption. Depending on
the processor workload, selecting this option may negatively impact performance.

Collaborative Power Control (G7 servers)

For Operating Systems that support the Processor Clocking Control (PCC) Interface, enabling this option
allows the Operating System to request processor frequency changes even when the server has the Power

Regulator option configured for Dynamic Power Savings Mode. For Operating Systems that do not
support the PCC Interface or when the Power Regulator Mode is not configured for Dynamic Power

Savings Mode, this option has no impact to system operation.

•

Enabled (Default)

«
...
40
41
42
43
44
...
»

Содержание ProLiant DL380e




























































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant DL380e

Бренд: Targus Страницы: 103

Бренд: PROLiNK Страницы: 12

SoundStation ITA

Бренд: Polycom Страницы: 12

AirStation WI-U2-433DM

Бренд: Buffalo Страницы: 29

N5192A UXG X-Series

Бренд: Keysight Страницы: 24

Бренд: Acard Страницы: 33

Бренд: Hama Страницы: 2

Бренд: NEC Страницы: 46

Бренд: Belkin Страницы: 168

Бренд: Alpine Страницы: 3

Бренд: MITSUBISHI ELECTRIC ENGINEERING Страницы: 2

Бренд: Corinex Страницы: 26

Бренд: Paradyne Страницы: 1

Бренд: Tumi Страницы: 127

SmartMedia (SM) Card/Adapter

Бренд: SimpleTech Страницы: 7

Бренд: Vanguard Instruments Страницы: 7

Бренд: ZJFKSDYX Страницы: 14

Бренд: Dongguan Binshi Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды