HP ProLiant DL380e Скачать руководство пользователя

Страница: 48 / 155

RBSU menu (HP ProLiant G7 servers or server blades) 48

Standard boot order (IPL) (G7 servers)

The Standard Boot Order (IPL) option configures the Initial IPL device and controls the search order the
server uses to look for a bootable device.

NOTE:

If you enable or disable a device, restart the server. Changes do not take effect until

after reboot.

Boot Controller Order (G7 servers)

The Boot Controller Order option selects which of the installed mass storage devices is used as the

primary boot controller. The server attempts to boot to the OS located on the primary boot controller.
The primary boot controller is set to controller 1.

NOTE:

Changes made to the Boot Controller Order in the ORCA Utility are reflected in this

menu.

Содержание ProLiant DL380e




























































































































































Результаты поиска

Содержание ProLiant DL380e

Отзывы:

Похожие инструкции для ProLiant DL380e

Бренды по названию

Популярные бренды

HP ProLiant DL380e, Руководство пользователя

Результаты поиска

Содержание ProLiant DL380e

Отзывы:

Похожие инструкции для ProLiant DL380e

Бренды по названию

Популярные бренды