HP ProLiant DL320e Скачать руководство пользователя страница 38

Страница: 38 / 204

Enable SATA RAID

NOTE:

This option is available only on server models that support Dynamic Smart Array. For

more information, see the HP Dynamic Smart Array RAID Controller User Guide on the HP website
at

http://www.hp.com/support/DSA_RAID_UG_en

This option allows the user to configure the embedded chipset serial ATA (SATA) controller to one
of three operational modes.

IMPORTANT:

•

Changing this setting may result in data loss or data corruption on existing drives.

•

Back up all drives before changing this setting.

•

Enable AHCI SATA support only after consulting the OS documentation to ensure that base
media drivers support this feature.

When this option is selected, the following warning is displayed:

After pressing any key to clear the warning, the following options are displayed:

•

Legacy SATA

•

AHCI SATA

•

HP SATA RAID

NOTE:

The default setting for this option is dependent on the server model.

RBSU menu-driven interface (G7 and later servers)

Содержание ProLiant DL320e













































































































































































































Результаты поиска

Содержание ProLiant DL320e

Отзывы:

HP ProLiant DL320e, Руководство пользователя, Страница: 38 / 204

Результаты поиска

Содержание ProLiant DL320e

Отзывы: