manualshive.com logo in svg

HP ProLiant DL320e, Руководство пользователя, Страница: 189 / 204

Поделиться
Скачать
HP ProLiant DL320e Скачать руководство пользователя страница 189

Setup Utility

Select

Setup Utility

from the System Maintenance menu to run the Setup Utility. Running Setup Utility

exits the System Maintenance menu and runs RBSU.

RBSU Erase option

The RBSU Erase option enables you to erase the system configuration and boot drive. On versions
of RBSU without this feature, the Erase Non-Volatile Memory option is available in the Advanced
Options menu of RBSU, enabling you to erase the system configuration by resetting the NVRAM
to an initial, factory state.

The Erase NVRAM/Boot Disk option also erases the system configuration by resetting the NVRAM,
but also erases the boot disk. The RBSU Erase option should only be used when you are redeploying
a server and are required to erase the NVRAM and boot drive to reinstall the operating system.
If available for the server, the Erase NVRAM/Boot Disk option is listed under the Advanced Options
menu in RBSU.

Virtual Install Disk option

The virtual install disk is a holding place within the system ROM that contains embedded boot
drivers (such as SCSI or RAID controller drivers) that may be necessary to complete the operating
system installation. Typically, boot drivers that are placed in the virtual install disk are either not
included as part of the operating system media or are updated for new controllers. Supported
operating systems automatically find these drivers, eliminating the need for user intervention. HP
recommends updating these boot drivers to the latest version after the OS install to further optimize
the system.

For more information, see:

•

G6 and earlier environments:

“Virtual Install Disk” (page 169)

•

Gen8 and G7 environments:

“Virtual Install Disk” (page 102)

The Virtual Install Disk option is found under the RBSU Advanced Options menu and can be enabled
or disabled in RBSU.

Inspect Utility

The Inspect Utility is embedded in the system ROM and enables you to view system configuration
information and save the information to a file on a diskette. Press the

F2

key to place all Inspect

information onto a diskette.

This utility replaces the version of the Inspect Utility that is a part of the legacy system-partition
functionality supported on some HP servers.

If the server has the Inspect Utility feature, select

Inspect Utility

from the System Maintenance menu.

Embedded server setup 189

Содержание ProLiant DL320e













































































































































































































Отзывы:

Нет отзывов