HP ProDesk 400 G4 Скачать руководство пользователя страница 85

Страница: 85 / 132

Network status link light never flashes.

NOTE:

The network status light is supposed to flash when there is network activity.

Cause

Solution

No active network is detected.

Check cabling and network equipment for proper connection.

Network controller is not set up properly.

Check for the device status within Windows, such as Device
Manager for driver load and the Network Connections applet
within Windows for link status.

To access Device Manager in Windows 7, click Start, select Control
Panel, and then select Device Manager.

To access Device Manager in Windows 10, type

device

manager

in the taskbar search box, and then select Device

Manager from the list of applications.

Network controller is disabled.

Run Computer Setup and enable network controller.

Enable the network controller in the operating system using
Device Manager.

To access Device Manager in Windows 7, click Start, select
Control Panel, and then select Device Manager.

To access Device Manager in Windows 10, type

device

manager

in the taskbar search box, and then select Device

Manager from the list of applications.

Network driver is not properly loaded.

Reinstall network drivers.

System cannot autosense the network.

Disable auto-sensing capabilities and force the system into
the correct operating mode.

Diagnostics reports a failure.

Cause

Solution

The cable is not securely connected.

Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely attached
to the correct device.

The cable is attached to the incorrect connector.

Ensure that the cable is attached to the correct connector.

There is a problem with the cable or a device at the other end of
the cable.

Ensure that the cable and device at the other end are operating
correctly.

The network controller is defective.

Contact an authorized service provider.

Diagnostics passes, but the computer does not communicate with the network.

Cause

Solution

Network drivers are not loaded, or driver parameters do not
match current configuration.

Make sure the network drivers are loaded and that the driver
parameters match the configuration of the network controller.

Make sure the correct network client and protocol is installed.

The network controller is not configured for this computer.

Select the Network and Sharing Center icon in the Control Panel
and configure the network controller.

Solving network problems

Содержание ProDesk 400 G4





































































































































Результаты поиска

Содержание ProDesk 400 G4

Отзывы:

Похожие инструкции для ProDesk 400 G4

Бренды по названию

Популярные бренды

HP ProDesk 400 G4, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProDesk 400 G4

Отзывы:

Похожие инструкции для ProDesk 400 G4

Бренды по названию

Популярные бренды