HP ProDesk 400 G4 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 132

background image

Rear panel components

(1)

Audio-out jack for power audio devices

(5)

USB 2.0 ports (4)

(2)

DisplayPort monitor connector

(6)

Audio-in jack

(3)

VGA monitor connector

(4)

RJ-45 (network) jack

(4)

USB 3.x ports (2)

(8)

Power cord connector

NOTE:

An optional second serial port and an optional parallel port are available from HP.

If using a USB keyboard, HP recommends connecting the keyboard to one of the USB 2.0 ports with the Wake from S4/S5 feature.

When a device is plugged into the audio-in jack, a dialog box will open asking if you want to use the connector for a microphone line-in
device or a headphone. You can reconfigure the connector at any time by double-clicking the Audio Manager icon in
the Windows® taskbar.

When a graphics card is installed in one of the system board slots, the video connectors on the graphics card and/or the integrated
graphics on the system board may be used. The specific graphics card installed and software configuration will determine the behavior.

The system board graphics can be disabled by changing settings in Computer Setup.

Rear panel components

3

«
...
9
10
11
12
13
...
»

Содержание ProDesk 400 G4





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProDesk 400 G4

Бренд: Acer Страницы: 30

Бренд: TechNexion Страницы: 37

Бренд: Vector Graphic Страницы: 40

Бренд: MicroTouch Страницы: 52

Height Adjustable Standing Desk 4-Leg

Бренд: Uplift Desk Страницы: 7

Бренд: Uplift Desk Страницы: 2

Бренд: IBM Страницы: 52

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 8

A20-S259 - Satellite - Pentium 4 2.66 GHz

Бренд: Toshiba Страницы: 12

Бренд: Toshiba Страницы: 50

Бренд: Toshiba Страницы: 56

dynaEdge DE-10 Series

Бренд: Toshiba Страницы: 137

Бренд: Toshiba Страницы: 181

Бренд: Toshiba Страницы: 183

Canvio Desk 3.5"

Бренд: Toshiba Страницы: 239

Бренд: Toshiba Страницы: 284

Бренд: Toshiba Страницы: 245

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды