HP ProDesk 400 G4 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 132

background image

Nonsystem disk/NTLDR missing message.

Cause

Solution

The system is trying to start from the hard drive but the hard
drive may have been damaged.

▲

Perform Drive Protection System (DPS) testing in system
ROM.

System files missing or not properly installed.

1.

Insert bootable media and restart the computer.

2.

Boot to the windows installation media and select
the recovery option. If only a restore kit is available, then
select the File Backup Program option, and then restore
the system.

3.

Install system files for the appropriate operating system.

Hard drive boot has been disabled in Computer Setup.

Run the Computer Setup utility and enable the hard drive entry in
the Advanced > Boot Options list.

Bootable hard drive is not attached as first in a multi-hard drive
configuration.

If attempting to boot from a hard drive, ensure it is attached to
the system board dark blue SATA connector.

Bootable hard drive is not listed first in the Boot Order.

Run the Computer Setup utility and select Advanced > Boot
Options and ensure the bootable hard drive is listed immediately
under the Hard Drive entry.

Computer will not boot from hard drive.

Cause

Solution

The device is attached to a SATA port that has been hidden in
Computer Setup.

1.

Check SATA cable connections.

2.

Run the Computer Setup utility and ensure Device Available
is selected for the device's SATA port in Advanced > Port
Options.

Boot order is not correct.

Run the Computer Setup utility and change boot sequence in
Advanced > Boot Options.

Hard drive is damaged.

Observe if the front panel Power LED is blinking RED and if any
beeps are heard. See

POST error messages and diagnostic front

panel LEDs and audible codes on page 85

to determine possible

causes for the blinking red and beep codes.

See the Worldwide Limited Warranty for terms and conditions.

Computer seems to be locked up.

Cause

Solution

Program in use has stopped responding to commands.

1.

Use the task manager to close programs that do not
respond.

2.

Attempt the normal Windows “Shut Down” procedure. If this
fails, press the power button for four or more seconds to
turn off the power. To restart the computer, press the power
button again.

Solving hard drive problems

63

«
...
69
70
71
72
73
...
»

Содержание ProDesk 400 G4





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProDesk 400 G4

Бренд: Acer Страницы: 26

UC-8100-ME-T Series

Бренд: Moxa Technologies Страницы: 22

Бренд: IBM Страницы: 2

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 3

Aspire Z5610 Series

Бренд: Acer Страницы: 2

Бренд: Acer Страницы: 4

Бренд: Acer Страницы: 52

Chromebase CA24I2

Бренд: Acer Страницы: 31

Бренд: Acer Страницы: 29

Aspire Z5600 Series

Бренд: Acer Страницы: 32

Бренд: Acer Страницы: 3

Бренд: Acer Страницы: 91

Бренд: Acer Страницы: 110

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 108

Бренд: Acer Страницы: 96

Бренд: Acer Страницы: 182

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды