HP ProCurve 1810G Скачать руководство пользователя страница 60

Страница: 60 / 80

8-2

Link Layer Discovery Protocol (LLPD)

LLDP Configuration

Table 8-1. LLDP Configuration Fields

■

Click

Apply

to save any changes for the current boot session; the changes take effect

immediately. Use the

Maintenance > Save Configuration

page to have the settings remain in effect

after a reboot.

To view LLDP statistics, click

Status > LLDP Statistics

in the navigation pane.

Field

Description

Global

Transmit Interval

Specify the interval at which frames are transmitted. The default is 30 seconds, and the
valid range is 5–32768 seconds.

Transmit Hold

Specify the multiplier on the transmit interval to assign to TTL (range 2–10, default = 4).

Re-Initialization Delay

Specify the delay before a re-initialization (range 1–10 seconds, default = 2).

Notification Interval

Specify a limit for the transmission of notifications (range 5–3600 seconds, default = 5).

Interface

The port to be affected by these parameters.

Transmit Enable

Enable or disable the transmission of LLDP PDUs. The default is enabled.

Receive Enable

Enable or disable the ability of the port to receive LLDP PDUs. The default is enabled.

Enable Notification

Enable to have LLDP generate a log file entry.

Transmit Mgmt Info

Enable or disable the transmission of management information with the LLDP PDUs. The
default is enabled.

Содержание ProCurve 1810G

















































































Результаты поиска

Содержание ProCurve 1810G

Отзывы:

Похожие инструкции для ProCurve 1810G

Бренды по названию

Популярные бренды

HP ProCurve 1810G, Руководство по управлению и настройке

Результаты поиска

Содержание ProCurve 1810G

Отзывы:

Похожие инструкции для ProCurve 1810G

Бренды по названию

Популярные бренды