HP ML350 - ProLiant - G2 Скачать руководство пользователя страница 68

Страница: 68 / 78

Component identification 68

System LED and color

Internal health LED

color

Status

Amber

A fan has failed but still meets the minimum fan

requirements (with redundant fan option only).

SAS and SATA hard drive LEDs

Item Description

Fault/UID LED (amber/blue)

Online LED (green)

SAS and SATA hard drive LED combinations

Online/activity LED

(green)

Fault/UID LED

(amber/blue)

Interpretation

On, off, or flashing Alternating amber

and blue

The drive has failed, or a predictive failure alert has been

received for this drive; it also has been selected by a

management application.

On, off, or flashing Steadily blue

The drive is operating normally, and it has been selected by a

management application.

Amber, flashing

regularly (1 Hz)

A predictive failure alert has been received for this drive.
Replace the drive as soon as possible.

Off

The drive is online, but it is not active currently.

Flashing regularly

(1 Hz)

Amber, flashing

regularly (1 Hz)

Do not remove the drive. Removing a drive may

terminate the current operation and cause data loss.

The drive is part of an array that is undergoing capacity

expansion or stripe migration, but a predictive failure alert has

been received for this drive. To minimize the risk of data loss, do

not replace the drive until the expansion or migration is

complete.

Содержание ML350 - ProLiant - G2















































































Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды

HP ML350 - ProLiant - G2, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды