HP ML350 - ProLiant - G2 Скачать руководство пользователя страница 72

Страница: 72 / 78

Specifications 72

Specification Value

LEDs (front panel)

Green = On

Read/write capacity per

diskette

High density

1.44 MB

Low density

720 KB

Drives supported

Drive height

One-third height

Drive rotation

300 rpm

Transfer rate

High 500

Kb/s

Low 250

Kb/s

Bytes/sector 512
Sectors per track (high/low)

18/9

Tracks per side (high/low)

80/80

Access times

Track-to-track (high/low)

3 ms/6 ms

Average (high/low)

169 ms/94 ms

Setting time

15 ms

Latency average

100 ms

Cylinders (high/low)

80/80

Read/write heads

FBDIMM specifications

CAUTION:

Be sure to install FBDIMMs in the proper configuration. Refer to the Documentation CD.

Item Description

Type

Registered DDR2 Fully Buffered DIMMs (FBDIMMs)

Size 512-MB,

1-GB,

2-GB

Width 72

bits

Upgrade requirement *

FBDIMMs must be installed in pairs within a bank, except

in single-FBDIMM mode, which supports a single 512-MB

FBDIMM installed in slot 1A. A bank must be populated

with 2 FBDIMMs with identical HP part numbers.

*Use only Registered DDR2 FBDIMMs. Use HP FBDIMMs only.

CD-ROM drive specifications

Specification Value

Disk formats

CD-ROM (modes 1 and 2); mixed mode (audio and data combined); CD-DA;

Photo CD (single/multiple-session), CD-XA ready; CDi ready

Capacity

550 MB (mode 1, 12 cm)

640 MB (mode 2, 12 cm)

Содержание ML350 - ProLiant - G2















































































Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды

HP ML350 - ProLiant - G2, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ML350 - ProLiant - G2

Отзывы:

Похожие инструкции для ML350 - ProLiant - G2

Бренды по названию

Популярные бренды