HP E1328A Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 70

HP E1328A Скачать руководство пользователя страница 50

Self-Test Errors

An error number (-330) is returned when the DAC self-test fails. If a
self-test error occurs, recycle power and repeat the self-test. If the error
repeats, see "Testing the DAC" to trouble shoot the DAC.

Operator Errors

Apparent failures may result from operator errors in sending SCPI messages
to the DAC. See Chapter 5 - 4-Channel D/A Converter Command
Reference in the HP E1328A User’s Manual for information on possible
SCPI command errors.

Catastrophic Failure

If a catastrophic failure occurs, see "Testing the DAC" to trouble shoot the
DAC.

Performance Out of Specification

If the DAC performance is out of specification limits, use the adjustment
procedures in Chapter 5 - Adjustments to correct the problem.
If the condition repeats, see "Testing the DAC" to trouble shoot the DAC.

Testing the DAC

Table 8-1 lists the error messages associated with the DAC. Based on the
error returned from the DAC, you can use the tests and checks in Table 8-2
to isolate the problem to a user replaceable part on the DAC rear panel or to
the A1 PCA. See Figure 6-1 in Chapter 6 - Replaceable Parts for locations
of user-replaceable parts.

NOTE

If the problem cannot be traced to a user-replaceable part listed in Table
6-1, return the counter to Hewlett-Packard for exchange. See Chapter 6 -
Replaceable Parts for procedures.

50 Service

Chapter

8

«
...
48
49
50
51
52
...
»

Содержание E1328A







































































Отзывы:

Нет отзывов