manualshive.com logo in svg

HP E1328A, Руководство по обслуживанию, Страница: 26 / 70

Поделиться
Скачать
HP E1328A Скачать руководство пользователя страница 26

Test Procedure

(Positive Current

Compliance)

1.  Set three jumpers on each channel to the I position

2.  Connect source and HP 3458A to Channel 1 (see Figure 4-2)

3.  Set non-cal mode on Channel 1 with CAL1:STAT OFF

4.  Set Channel 1 max output (+24 mA) with CURR1 MAX

5.  Set DC source to + 12.0V and measure channel output (in mA)

6.  Increase DC source output by +0.5V and measure channel output (in mA)

7.  Repeat step 6 until channel output is 90% of max (21.6 mA). If the

SOURCE voltage is 

≥

 13.0V when the output decreases to 90% of max, the

test passes.

8.  Repeat steps 2 through 7 for Channels 2, 3, and 4. (Use CALchan:STAT

OFF and CURRchan MAX.)

9.  Remove power and disconnect test equipment

Test Procedure

(Negative Current

Compliance)

1.  Set three jumpers on each channel to the I position

2.  Connect source and HP 3458A to Channel 1 (see Figure 4-2)

3.  Set non-cal mode on Channel 1 with CAL1:STAT OFF

4.  Set Channel 1 min current output (-24 mA) with CURR1 MIN

5.  Set DC source to -12.0V and measure channel output (in mA)

6.  Increase DC source output by -0.5V and measure channel output (in mA)

7.  Repeat step 6 until channel output is 90% of min (-21.6 mA). If the

SOURCE voltage is 

≤

 -13.0V when the output decreases to 90% of min, the

test passes.

8.  Repeat steps 2 through 7 for Channels 2, 3, and 4 (use CAL chan:STAT

OFF and CURR chan MIN)

26  Verification Tests

Chapter 4

Содержание E1328A







































































Отзывы:

Нет отзывов