HP dc7700 - Convertible Minitower PC Скачать руководство пользователя

Страница: 49 / 72

Solving Drive Key Problems

If you encounter Drive Key problems, common causes and solutions are listed in the following table.

Table 2-16

Solving Drive Key Problems

USB Drive Key is not seen as a drive letter in Windows.

Cause

Solution

The drive letter after the last physical drive is not available.

Change the default drive letter for the Drive Key in Windows.

USB Drive Key not found (identified).

Cause

Solution

The device is attached to a USB port that has been hidden in
Computer Setup.

Run the Computer Setup utility and ensure that "Device
available" is selected for "All USB Ports" and "Front USB Ports"
under

Security

Device Security

The device was not properly seated before power-up.

Ensure the device is fully inserted into the USB port before
applying power to the system

System will not boot from USB Drive Key.

Cause

Solution

Boot order is not correct.

Run the Computer Setup utility and change boot sequence
in

Storage

Boot Order

Removable Media Boot is disabled in the Computer Setup
utility.

Run the Computer Setup utility and enable booting to
removable media in

Storage

Storage Options

. Ensure USB

is enabled in

Storage

Boot Order

The image on the device is not bootable.

Follow the procedures described in the "ROM Flash:
Replicating the Setup: Creating a Bootable Device: Supported
USB Flash Media Device" section of the

Service Reference

Guide

The computer boots to DOS after making a bootable Drive Key.

Cause

Solution

Drive Key is bootable.

Install the Drive Key only after the operating system boots.

ENWW

Solving Drive Key Problems

Содержание dc7700 - Convertible Minitower PC









































































Результаты поиска

Содержание dc7700 - Convertible Minitower PC

Отзывы:

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренды по названию

Популярные бренды

HP dc7700 - Convertible Minitower PC, Руководство по устранению неисправностей

Результаты поиска

Содержание dc7700 - Convertible Minitower PC

Отзывы:

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренды по названию

Популярные бренды