HP dc7700 - Convertible Minitower PC Скачать руководство пользователя

Страница: 62 / 72

Control panel message

Description

Recommended action

2204-Inventory error during MEBx execution BIOS information passed to the MEBx

resulted in a failure.

Reboot the computer.

If the error persists, update to the latest
BIOS version.

If the error still persists, replace the
system board.

2205-Interface error during MEBx execution

MEBx operation experienced a hardware
error during communication with ME.

Reboot the computer.

If the error persists, update to the latest
BIOS version.

If the error still persists, replace the
system board.

Invalid Electronic Serial Number

Electronic serial number is missing.

Enter the correct serial number in Computer
Setup.

Network Server Mode Active and No
Keyboard Attached

Keyboard failure while Network Server Mode
enabled.

Reconnect keyboard with computer
turned off.

Check connector for bent or missing
pins.

Ensure that none of the keys are
depressed.

Replace keyboard.

Parity Check 2

Parity RAM failure.

Run Computer Setup and Diagnostic utilities.

System will not boot without fan

CPU fan not installed or disconnected in
VSFF chassis.

Remove the computer cover, press the
power button, and see if the processor
fan spins. If the processor fan is not
spinning, make sure the fan's cable is
plugged onto the system board header.
Ensure the heatsink is properly seated
and installed.

If the fan is plugged in and the heatsink
is properly seated but the fan does not
spin, then replace the heatsink-fan
assembly.

Table A-1

Numeric Codes and Text Messages (continued)

Appendix A POST Error Messages

ENWW

Содержание dc7700 - Convertible Minitower PC









































































Результаты поиска

Содержание dc7700 - Convertible Minitower PC

Отзывы:

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренды по названию

Популярные бренды

HP dc7700 - Convertible Minitower PC, Руководство по устранению неисправностей

Результаты поиска

Содержание dc7700 - Convertible Minitower PC

Отзывы:

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренды по названию

Популярные бренды