HP dc7700 - Convertible Minitower PC Скачать руководство пользователя

Страница: 42 / 72

Network controller stopped working when an expansion board was added to the computer.

Cause

Solution

Network controller interrupt is shared with an expansion board. Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

The network controller requires drivers.

Verify that the drivers were not accidentally deleted when the
drivers for a new expansion board were installed.

The expansion board installed is a network card (NIC) and
conflicts with the embedded NIC.

Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

Network controller stops working without apparent cause.

Cause

Solution

The files containing the network drivers are corrupted.

Reinstall the network drivers, using the

Restore Plus!

CD.

The cable is not securely connected.

Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely
attached to the correct device.

The network controller is defective.

Contact an authorized service provider.

New network card will not boot.

Cause

Solution

New network card may be defective or may not meet industry-
standard specifications.

Install a working, industry-standard NIC, or change the boot
sequence to boot from another source.

Cannot connect to network server when attempting Remote System Installation.

Cause

Solution

The network controller is not configured properly.

Verify Network Connectivity, that a DHCP Server is present,
and that the Remote System Installation Server contains the
NIC drivers for your NIC.

System setup utility reports unprogrammed EEPROM.

Cause

Solution

Unprogrammed EEPROM.

Contact an authorized service provider.

Table 2-12

Solving Network Problems (continued)

Chapter 2 Troubleshooting Without Diagnostics

ENWW

Содержание dc7700 - Convertible Minitower PC









































































Результаты поиска

Содержание dc7700 - Convertible Minitower PC

Отзывы:

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренды по названию

Популярные бренды

HP dc7700 - Convertible Minitower PC, Руководство по устранению неисправностей

Результаты поиска

Содержание dc7700 - Convertible Minitower PC

Отзывы:

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренды по названию

Популярные бренды