HP dc7700 - Convertible Minitower PC Скачать руководство пользователя | Manualshive

Страница: 46 / 72

background image

Solving CD-ROM and DVD Problems

If you encounter CD-ROM or DVD problems, see the common causes and solutions listed in the
following table or to the documentation that came with the optional device.

Table 2-15

Solving CD-ROM and DVD Problems

System will not boot from CD-ROM or DVD drive.

Cause

Solution

The device is attached to a SATA port that has been disabled
in the Computer Setup utility.

Run the Computer Setup utility and ensure the device's SATA
port is enabled in

Storage

>

Storage Options

.

Removable Media Boot is disabled in the Computer Setup
utility.

Run the Computer Setup utility and enable booting to
removable media in

Storage

>

Storage Options

. Ensure CD-

ROM is enabled in

Storage

>

Boot Order

.

Network Server Mode is enabled in Computer Setup.

Run the Computer Setup utility and disable Network Server
Mode in

Security

>

Password Options

.

Non-bootable CD in drive.

Try a bootable CD in the drive.

Boot order not correct.

Run the Computer Setup utility and change boot sequence
in

Storage

>

Boot Order

.

Drive not found (identified).

Cause

Solution

Cable could be loose.

Check cable connections.

The system may not have automatically recognized a newly
installed device.

See reconfiguration directions in the

Solving Hardware

Installation Problems on page 32

section. If the system still

does not recognize the new device, check to see if the device
is listed within Computer Setup. If it is listed, the probable
cause is a driver problem. If it is not listed, the probable cause
is a hardware problem.

If this is a newly installed drive, run the Computer Setup utility
and try adding a POST delay under

Advanced

>

Power-On

.

The device is attached to a SATA port that has been disabled
in Computer Setup.

Run the Computer Setup utility and ensure the device's SATA
port is enabled in

Storage

>

Storage Options

.

Drive responds slowly immediately after power-up.

Run Computer Setup and increase the POST Delay in

Advanced

>

Power-On Options

.

CD-ROM or DVD devices are not detected or driver is not loaded.

Cause

Solution

Drive is not connected properly or not properly configured.

See the documentation that came with the optional device.

40

Chapter 2 Troubleshooting Without Diagnostics

ENWW

«
...
44
45
46
47
48
...
»

Содержание dc7700 - Convertible Minitower PC









































































Отзывы:

Нет отзывов

Похожие инструкции для dc7700 - Convertible Minitower PC

Бренд: F-SECURE Страницы: 18

Бренд: Davis Instruments Страницы: 108

ClearPass Guest 3.9

Бренд: Aruba Networks Страницы: 518

TICKETMASTER - LEARN MORE

Бренд: Blackberry Страницы: 7

IP Office CTI Link

Бренд: Avaya Страницы: 28

JBoss Developer Studio 3.0

Бренд: Red Hat Страницы: 78

Бренд: MACROMEDIA Страницы: 830

PTF100NTU - LCD PROJECTOR

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 10

Media Manager V2.1

Бренд: Panasonic Страницы: 28

Lumix VQT0U14 ( )

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 70

PANATERM Ver. 3.7

Бренд: Panasonic Страницы: 78

Voice Editing Ver.2.0

Бренд: Panasonic Страницы: 132

Бренд: Panasonic Страницы: 156

Бренд: ADS Technologies Страницы: 2

Бренд: TRENDnet Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды