HP dc5700 - Microtower PC Скачать руководство пользователя

Страница: 35 / 71

Solving Printer Problems

If you encounter printer problems, see the documentation that came with the printer and to the common
causes and solutions listed in the following table.

Table 2-8

Solving Printer Problems

Printer will not print.

Cause

Solution

Printer is not turned on and online.

Turn the printer on and make sure it is online.

The correct printer drivers for the application are not installed.

Install the correct printer driver for the application.

Try printing using the MS-DOS command:

DIR C:\ > LPT1

If the printer works, reload the printer driver.

If you are on a network, you may not have made the connection
to the printer.

Make the proper network connections to the printer.

Printer may have failed.

Run printer self-test.

Printer will not turn on.

Cause

Solution

The cables may not be connected properly.

Reconnect all cables and check the power cord and electrical
outlet.

Printer prints garbled information.

Cause

Solution

The correct printer driver for the application is not installed.

Install the correct printer driver for the application.

The cables may not be connected properly.

Reconnect all cables.

Printer memory may be overloaded.

Reset the printer by turning it off for one minute, then turn it
back on.

Printer is offline.

Cause

Solution

The printer may be out of paper.

Check the paper tray and refill it if it is empty. Select online.

ENWW

Solving Printer Problems

Содержание dc5700 - Microtower PC








































































Результаты поиска

Содержание dc5700 - Microtower PC

Отзывы:

Похожие инструкции для dc5700 - Microtower PC

Бренды по названию

Популярные бренды

HP dc5700 - Microtower PC, Руководство по устранению неисправностей

Результаты поиска

Содержание dc5700 - Microtower PC

Отзывы:

Похожие инструкции для dc5700 - Microtower PC

Бренды по названию

Популярные бренды