HP dc5700 - Microtower PC Скачать руководство пользователя | Manualshive

Страница: 29 / 71

background image

Solving Display Problems

If you encounter display problems, see the documentation that came with the monitor and to the common
causes and solutions listed in the following table.

Table 2-6

Solving Display Problems

Blank screen (no video).

Cause

Solution

Monitor is not turned on and the monitor light is not on.

Turn on the monitor and check that the monitor light is on.

Bad monitor.

Try a different monitor.

The cable connections are not correct.

Check the cable connection from the monitor to the computer
and to the electrical outlet.

You may have a screen blanking utility installed or energy
saver features are enabled.

Press any key or click the mouse button and, if set, type your
password.

System ROM is corrupted; system is running in Boot Block
Emergency Recovery Mode (indicated by eight beeps).

Reflash the system ROM with the latest BIOS image. See the
“Boot Block Emergency Recovery Mode” section of the

Desktop Management Guide

on the

Documentation and

Diagnostics CD

for more information.

You are using a fixed-sync monitor and it will not sync at the
resolution chosen.

Be sure that the monitor can accept the same horizontal scan
rate as the resolution chosen.

Computer is in

standby

mode.

Press the power button to resume from

standby

mode.

CAUTION:

When attempting to resume from

standby

mode, do not hold down the power button for

more than four seconds. Otherwise, the computer will
shut down and you will lose any unsaved data.

Monitor cable is plugged into the wrong connector.

Ensure that the monitor is plugged into an active connector on
the rear of the computer. If another connector is available,
connect the monitor to that connector and reboot the system.

Monitor settings in the computer are not compatible with the
monitor.

1.

In Windows XP Control Panel, double-click the

Display

icon and select the

Settings

tab.

In Windows Vista Control Panel, under

Appearance and

Personalization

, select

Adjust screen resolution

.

2.

Use the sliding control to reset the resolution.

Cannot enable integrated graphics after installing a PCI Express graphics card.

Cause

Solution

The SDVO connector on the system board has the physical
appearance of a PCI Express x16 connector; however, the
platform does NOT support the use of conventional PCI
Express cards or reversed-layout ADD2 cards.

The platform only supports the use of normal (or non-reversed)
layout ADD2 (Advanced Digital Display 2) adapter cards
inserted into the SDVO (Serial Digital Video Output) connector
on the platform's system board. ADD2 cards are used to give
multi-monitor capabilities to the integrated graphics controller.

ENWW

Solving Display Problems

23

«
...
27
28
29
30
31
...
»

Содержание dc5700 - Microtower PC








































































Отзывы:

Нет отзывов

Похожие инструкции для dc5700 - Microtower PC

Бренд: Garmin Страницы: 12

MOBILE SECURITY FOR WINDOWS MOBILE -

Бренд: F-SECURE Страницы: 4

MOBILE SECURITY FOR UIQ -

Бренд: F-SECURE Страницы: 3

MOBILE SECURITY 6 FOR WINDOWS MOBILE -

Бренд: F-SECURE Страницы: 5

MOBILE SECURITY 6 FOR S60 -

Бренд: F-SECURE Страницы: 5

CLIENT SECURITY 7.00

Бренд: F-SECURE Страницы: 315

ANTI-VIRUS FOR MICROSOFT EXCHANGE 9.00

Бренд: F-SECURE Страницы: 115

ANTI-VIRUS FOR MICROSOFT EXCHANGE 8.00 -

Бренд: F-SECURE Страницы: 349

ANTI-VIRUS - FOR MICROSOFT EXCHANGE

Бренд: F-SECURE Страницы: 224

Linear-Phase MultiBand Software Audio Processor

Бренд: Waves Страницы: 27

CORPORATE SUITE

Бренд: KAPERSKY Страницы: 36

SmartNode Series

Бренд: Patton electronics Страницы: 655

Бренд: Brocade Communications Systems Страницы: 41

PlateRunner P24 Processor

Бренд: Xante Страницы: 6

Бренд: Minolta Страницы: 26

Бренд: Billion Страницы: 18

PCANYWHERE - V12.1

Бренд: Symantec Страницы: 321

Бренд: Remote Reality Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды