HP dc5700 - Microtower PC страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 71

background image

●

Check the Power LED on the front of the computer to see if it is flashing red. The flashing lights
are error codes that will help you diagnose the problem. Refer to Appendix A,

POST Error

Messages on page 49

for more information.

●

Turn up the brightness and contrast controls of the monitor if the monitor is dim.

●

Press and hold any key. If the system beeps, then the keyboard should be operating correctly.

●

Check all cable connections for loose connections or incorrect connections.

●

Wake the computer by pressing any key on the keyboard or pressing the power button. If the system
remains in suspend mode, shut down the computer by pressing and holding the power button for
at least four seconds then press the power button again to restart the computer. If the system will
not shut down, unplug the power cord, wait a few seconds, then plug it in again. The computer will
restart if automatic start on power loss is set in Computer Setup. If it does not restart, press the
power button to start the computer.

●

Reconfigure the computer after installing a non–plug and play expansion board or other option.
See

Solving Hardware Installation Problems on page 32

for instructions.

●

Be sure that all the needed device drivers have been installed. For example, if you are using a
printer, you need a driver for that model printer.

●

Remove all bootable media (diskette, CD, or USB device) from the system before turning it on.

●

If you have installed an operating system other than the factory-installed operating system, check
to be sure that it is supported on the system.

●

If the system has multiple video sources (embedded, PCI, or PCI-Express adapters) installed
(embedded video on some models only) and a single monitor, the monitor must be plugged into
the monitor connector on the source selected as the primary VGA adapter. During boot, the other
monitor connectors are disabled and if the monitor is connected into these ports, the monitor will
not function. You can select which source will be the default VGA source in Computer Setup.

CAUTION:

When the computer is plugged into an AC power source, there is always voltage

applied to the system board. You must disconnect the power cord from the power source before
opening the computer to prevent system board or component damage.

ENWW

Helpful Hints

9

«
...
13
14
15
16
17
...
»

Содержание dc5700 - Microtower PC








































































Отзывы:

Нет отзывов

Похожие инструкции для dc5700 - Microtower PC

Бренд: Cabletron Systems Страницы: 16

Бренд: Arturia Страницы: 10

Бренд: Campbell Страницы: 250

Бренд: Packet8 Страницы: 43

K2-AVID TRANSFER MANAGER

Бренд: GRASS VALLEY Страницы: 2

ANTI-VIRUS 5.5 - FOR MICROSOFT EXCHANGE SERVER 2000-2003

Бренд: KAPERSKY Страницы: 143

Unified Messaging

Бренд: Oracle Страницы: 46

Retail Place 12.2

Бренд: Oracle Страницы: 68

Oracle Web Application Server

Бренд: Oracle Страницы: 80

Oracle Territory Management

Бренд: Oracle Страницы: 98

PHOTO EXPRESS MD 5345

Бренд: Ulead Страницы: 43

Бренд: Ulead Страницы: 24

FLASH MX 2004-DATA

Бренд: MACROMEDIA Страницы: 20

ANTI-VIRUS 4.5 - FOR MICROSOFT EXCHANGE...

Бренд: KAPERSKY Страницы: 134

Бренд: ICP Страницы: 6

Бренд: NEC Страницы: 57

Бренд: Igo Страницы: 12

dc5100 - Microtower PC

Бренд: HP Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды