HP dc5700 - Microtower PC страница 25 Скачать руководство пользователя

Страница: 25 / 71

Nonsystem disk/NTLDR missing message.

Cause

Solution

The system is trying to start from a diskette that is not bootable. Remove the diskette from the diskette drive.

The system is trying to start from the hard drive but the hard
drive may have been damaged.

Insert a bootable diskette into the diskette drive and
restart the computer.

Check the hard drive format using fdisk: If NTFS
formatting, use a third party reader to evaluate the drive.
If FAT32 formatting, the hard drive cannot be accessed.

System files missing or not properly installed.

Insert a bootable diskette into the diskette drive and
restart the computer.

Check the hard drive format using Fdisk: If NTFS
formatting, use a third party reader to evaluate the drive.
If FAT32 formatting, the hard drive cannot be accessed.

Install system files for the appropriate operating system.

Restore the system to a recovery point in HP Backup and
Recovery Manager. Refer to the

HP Backup and

Recovery Manager User Guide

in the Windows Start

menu for more information.

Hard drive boot has been disabled in Computer Setup.

Run the Computer Setup utility and enable the hard drive entry
in the

Storage

Boot Order

list.

Bootable hard drive is not attached as first in a multi-hard drive
configuration.

If attempting to boot from a hard drive, ensure it is attached to
the system board connector labeled P60 SATA 0.

Bootable hard drive's controller is not listed first in the Boot
Order.

Run the Computer Setup utility and select

Storage

Boot

Order

and ensure the bootable hard drive's controller is listed

immediately under the

Hard Drive

entry.

Computer will not boot from hard drive.

Cause

Solution

The device is attached to a SATA port that has been disabled
in Computer Setup.

Run the Computer Setup utility and ensure the device's SATA
port is enabled in

Storage

Storage Options

Legacy operating system does not support boot devices
attached to SATA 4 or SATA 5 ports.

Connect boot devices to SATA 0 or SATA 1 ports.

Boot order is not correct.

Run the Computer Setup utility and change boot sequence
in

Storage

Boot Order

Hard Drive's "Emulation Type" is set to "None."

Run the Computer Setup utility and change the "Emulation
Type" to "Hard Disk" in the device's details under

Storage

Device Configuration

The device is attached to a SATA port that has been disabled
in Computer Setup.

Run the Computer Setup utility and ensure the device's SATA
port is enabled in

Storage

Storage Options

Hard drive is damaged.

Observe if the front panel Power LED is blinking RED and if
any beeps are heard. See Appendix A,

POST Error

Messages on page 49

to determine possible causes for the

blinking red and beep codes.

See the Worldwide Limited Warranty for terms and conditions.

Table 2-4

Solving Hard Drive Problems (continued)

ENWW

Solving Hard Drive Problems

Содержание dc5700 - Microtower PC








































































Результаты поиска

Содержание dc5700 - Microtower PC

Отзывы:

Похожие инструкции для dc5700 - Microtower PC

Бренды по названию

Популярные бренды

HP dc5700 - Microtower PC, Руководство по устранению неисправностей

Результаты поиска

Содержание dc5700 - Microtower PC

Отзывы:

Похожие инструкции для dc5700 - Microtower PC

Бренды по названию

Популярные бренды