HP D530 - Compaq Business Desktop Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 77

background image

F

Electrostatic Discharge

A discharge of static electricity from a finger or other conductor may damage system
boards or other static-sensitive devices. This type of damage may reduce the life
expectancy of the device.

Preventing Electrostatic Damage

To prevent electrostatic damage, observe the following precautions:

Avoid hand contact by transporting and storing products in static-safe containers.

Keep electrostatic-sensitive parts in their containers until they arrive at static-free
workstations.

Place parts on a grounded surface before removing them from their containers.

Avoid touching pins, leads, or circuitry.

Always be properly grounded when touching a static-sensitive component or
assembly.

Grounding Methods

There are several methods for grounding. Use one or more of the following methods
when handling or installing electrostatic-sensitive parts:

Use a wrist strap connected by a ground cord to a grounded work station or
computer chassis. Wrist straps are flexible straps with a minimum of 1 megohm
+/- 10 percent resistance in the ground cords. To provide proper ground, wear the
strap snug against the skin.

Hardware Reference Guide

F-1

«
...
68
69
70
71
72
...
»

Содержание D530 - Compaq Business Desktop














































































Отзывы:

Нет отзывов

Похожие инструкции для D530 - Compaq Business Desktop

IntelliJack NJ200

Бренд: 3Com Страницы: 14

TRANSCEND EM/NT 6.3

Бренд: 3Com Страницы: 39

IronKey Workspace Provisioning Tool 1.0

Бренд: Imation Страницы: 19

Бренд: deXlan Страницы: 17

FLASH 8-USING FLASH VIDEO ENCODER

Бренд: MACROMEDIA Страницы: 30

WISE MOBILE DEVICE PACKAGE EDITOR 7.0 SP2

Бренд: Symantec Страницы: 22

Бренд: Toshiba Страницы: 1

dynadock Drivers

Бренд: Toshiba Страницы: 3

e-STUDIO Printer/Fax/Scanner/Copier

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 53

PARTNER ACS R5.0

Бренд: Avaya Страницы: 32

Бренд: I.R.I.S. Страницы: 10

IRISPOWERSCAN 9.0

Бренд: I.R.I.S. Страницы: 153

Converter Studio

Бренд: Elecard Страницы: 76

Бренд: Cyber Sciences Страницы: 2

Бренд: GRASS VALLEY Страницы: 2

Бренд: beat buddy Страницы: 33

Бренд: FieldServer Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды