HP D530 - Compaq Business Desktop Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 77

background image

Hardware Upgrades

Removing the AGP Card

A 1.5V low profile Accelerated Graphics Port (AGP) card may be installed in the
AGP slot on the system board. To remove the AGP card from the AGP slot:

1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the

lock.

2. Turn off the computer properly through the operating system, then turn off any

external devices.

3. Disconnect the power cord from the power outlet and disconnect any external

devices.

4. Remove the computer access panel.

5. Locate the AGP card on the system board.

6. Lift up the slot cover retention latch that secures the AGP card.

Hardware Reference Guide

2-17

«
...
25
26
27
28
29
...
»

Содержание D530 - Compaq Business Desktop














































































Отзывы:

Нет отзывов

Похожие инструкции для D530 - Compaq Business Desktop

Бренд: NEC Страницы: 4

Бренд: ITech Страницы: 22

NG Network Access Client SP4

Бренд: Barracuda Networks Страницы: 10

Бренд: AMX Страницы: 12

Бренд: Alcatel Страницы: 4

Бренд: Amazon Страницы: 60

Бренд: Nokia Страницы: 29

Бренд: Nokia Страницы: 29

Бренд: Nokia Страницы: 35

NPS6113000 - Secure Access System

Бренд: Nokia Страницы: 48

N73 - Smartphone 42 MB

Бренд: Nokia Страницы: 354

N73 - Smartphone 42 MB

Бренд: Nokia Страницы: 265

Network Voyager

Бренд: Nokia Страницы: 700

STRM 2008.2R2 - UPGRADING TO STRM 2008.2R2 REV 2

Бренд: Juniper Страницы: 5

Бренд: MACROMEDIA Страницы: 678

FS-8704-14 EtherNet

Бренд: FieldServer Страницы: 30

MEDIASTUDIO PRO 7.0 - HD PLUG-IN 2.0

Бренд: Ulead Страницы: 11

Бренд: RADVision Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды