HP D530 - Compaq Business Desktop Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 77

background image

Hardware Upgrades

7. Replace with the appropriate bezel by pushing the bezel into place.

The type of bezel you need will depend on the type of device you are installing. If
you are installing a diskette drive, you must install a diskette drive bezel (PN 316002-
001). If you are installing a hard drive, you must install a bezel blank (PN 316006-
001) as shown in the illustration below. If you are installing a 3.5-inch device other
than a diskette drive or hard drive, you must install the 3.5-inch device bezel (PN
316008-001). Contact an authorized HP reseller or service provider to order the
appropriate bezel when reconfiguring the computer.

8. Connect the power and data cables.

9. Replace the front bezel and computer access panel.

Hardware Reference Guide

2-35

«
...
43
44
45
46
47
...
»

Содержание D530 - Compaq Business Desktop














































































Отзывы:

Нет отзывов

Похожие инструкции для D530 - Compaq Business Desktop

Бренд: Generic Media Страницы: 17

Бренд: NETGEAR Страницы: 2

JUNOS PUS MOBILE SECURITY SUITE

Бренд: Juniper Страницы: 6

Бренд: Brocade Communications Systems Страницы: 64

PRIVILEGED USER MANAGER 2.2

Бренд: Novell Страницы: 37

Бренд: Pioneer Страницы: 11

LINUX ENTERPRISE DESKTOP 10 SP1 -

Бренд: Linux Страницы: 76

CERTIFICATE SYSTEM 6.0 - MIGRATION GUIDE

Бренд: Red Hat Страницы: 76

Бренд: Vitek Страницы: 1

APPLICATION STACK 2.2 RELEASE

Бренд: Red Hat Страницы: 22

TWIG CONFIGURATOR

Бренд: Benefon Страницы: 28

K2-AVID TRANSFER MANAGER

Бренд: GRASS VALLEY Страницы: 2

Бренд: UNIBLUE Страницы: 3

TIVOLI ADSTAR 5697-VM3

Бренд: IBM Страницы: 62

Бренд: Xerox Страницы: 32

magicolor 2590MF

Бренд: 3D Nord Страницы: 198

ThinkCentre M62z

Бренд: Lenovo Страницы: 126

Бренд: DANE-ELEC Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды