HP Compaq dx7400 Series Скачать руководство пользователя страница 59

Страница: 59 / 69

Control panel message

Description

Recommended action

1720-SMART Hard Drive Detects Imminent
Failure

Hard drive is about to fail. (Some hard drives
have a hard drive firmware patch that will fix
an erroneous error message.)

Determine if hard drive is giving correct
error message. Enter Computer Setup
and run the Drive Protection System test
under

Storage

DPS Self-test

Apply hard drive firmware patch
if applicable. (Available at

http://www.hp.com/support

Back up contents and replace hard
drive.

1796-SATA Cabling Error

One or more SATA devices are improperly
attached. For optimal performance, the SATA
0 and SATA 1 connectors must be used
before SATA 2 and SATA 3.

Ensure SATA connectors are used in
ascending order. For one device, use SATA
0. For two devices, use SATA 0 and SATA 1.
For three devices, use SATA 0, SATA1, and
SATA 2.

1797-SATA Drivelock is not supported in
RAID mode.

Drivelock is enabled on one or more SATA
hard drives, and they cannot be accessed
while the system is configured for RAID
mode.

Either remove the Drivelocked SATA device
or disable the Drivelock feature. To disable
the Drivelock feature, enter Computer Setup,
change

Storage

Storage Options

SATA

Emulation

IDE

, and select

File

Save

Changes and Exit

. Reenter Computer Setup

and select

Security

Drivelock

. For each

listed Drivelock-capable SATA device,
ensure Drivelock is

Disabled

. Lastly, change

Storage

Storage Options

SATA

Emulation

back to

RAID

and select

File

Save Changes and Exit

1801-Microcode Patch Error

Processor is not supported by ROM BIOS.

Upgrade BIOS to proper version.

Change the processor.

2200-PMM Allocation Error during MEBx
Download

Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM

Reboot the computer.

Unplug the power cord, re-seat the
memory modules, and reboot the
computer.

If the memory configuration was
recently changed, unplug the computer,
restore the original memory
configuration, and reboot the computer.

If the error persists, replace the system
board.

2201-MEBx Module did not checksum
correctly

Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM

Reboot the computer.

Unplug the power cord, re-seat the
memory modules, and reboot the
computer.

If the memory configuration was
recently changed, unplug the power
cord, restore the original memory
configuration, and reboot the computer.

If the error persists, replace the system
board.

2202-PMM Deallocation Error during MEBx
cleanup

Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM

Reboot the computer.

Unplug the power cord, re-seat the
memory modules, and reboot the
computer.

Table A-1

Numeric Codes and Text Messages (continued)

ENWW

POST Numeric Codes and Text Messages

Содержание Compaq dx7400 Series






































































Результаты поиска

Содержание Compaq dx7400 Series

Отзывы:

Похожие инструкции для Compaq dx7400 Series

Бренды по названию

Популярные бренды

HP Compaq dx7400 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание Compaq dx7400 Series

Отзывы:

Похожие инструкции для Compaq dx7400 Series

Бренды по названию

Популярные бренды