HP Compaq dx7400 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 69

background image

Solving Display Problems

If you encounter display problems, see the documentation that came with the monitor and to the common
causes and solutions listed in the following table.

Table 2-6

Solving Display Problems

Blank screen (no video).

Cause

Solution

Monitor is not turned on and the monitor light is not on.

Turn on the monitor and check that the monitor light is on.

Bad monitor.

Try a different monitor.

The cable connections are not correct.

Check the cable connection from the monitor to the computer
and to the electrical outlet.

You may have a screen blanking utility installed or energy
saver features are enabled.

Press any key or click the mouse button and, if set, type your
password.

System ROM is corrupted; system is running is Boot Block
Emergency Recovery Mode (indicated by eight beeps).

Reflash the system ROM with the latest BIOS image. See the
“Boot Block Emergency Recovery Mode” section of the

Desktop Management Guide

for more information

You are using a fixed-sync monitor and it will not sync at the
resolution chosen.

Be sure that the monitor can accept the same horizontal scan
rate as the resolution chosen.

Computer is in

standby

mode.

Press the power button to resume from

standby

mode.

CAUTION:

When attempting to resume from

standby

mode,

do not hold down the power button for more than four seconds.
Otherwise, the computer will shut down and you will lose any
unsaved data.

Monitor cable is plugged into the wrong connector.

If the computer system has both an integrated graphics
connector and an add-in graphics card connector, plug the
monitor cable into the graphics card connector on the back of
the computer.

Monitor settings in the computer are not compatible with the
monitor.

1.

In Windows XP Control Panel, double-click the

Display

icon and select the

Settings

tab.

In Windows Vista Control Panel, under

Appearance and

Personalization

, select

Adjust screen resolution

.

2.

Use the sliding control to reset the resolution.

Cannot enable integrated graphics after installing a PCI Express graphics card.

Cause

Solution

On systems with Intel integrated graphics, the integrated
graphics cannot be enabled after installing a PCI Express x16.

The integrated graphics can be enabled in Computer Setup if
a PCI or PCI Express x1 graphics card is installed, but it cannot
be enabled if there is a graphics card in the PCI Express x16
slot.

Blank screen and the power LED flashes Red five times, once every second, followed by a two second pause, and the
computer beeps five times. (Beeps stop after fifth iteration but LEDs continue flashing.)

Cause

Solution

Pre-video memory error.

1.

Reseat DIMMs. Power on the system.

2.

Replace DIMMs one at a time to isolate the faulty module.

ENWW

Solving Display Problems

23

«
...
27
28
29
30
31
...
»

Содержание Compaq dx7400 Series






































































Отзывы:

Нет отзывов

Похожие инструкции для Compaq dx7400 Series

Бренд: Raven Страницы: 71

st5548 - Thin Client

Бренд: Compaq Страницы: 39

Бренд: Gateway Страницы: 144

Mephisto Polgar

Бренд: Hegener+Glaser Страницы: 19

Precision 3640 Tower

Бренд: Dell Страницы: 112

SIMATIC IPC847C

Бренд: Siemens Страницы: 46

SIMATIC PC RI25

Бренд: Siemens Страницы: 64

SIMATIC Panel PC 677

Бренд: Siemens Страницы: 94

SIMATIC PG 760 PII

Бренд: Siemens Страницы: 120

Бренд: Siemens Страницы: 192

SIMATIC IPC847D

Бренд: Siemens Страницы: 222

MEC-5007 Series

Бренд: EVOC Страницы: 80

Бренд: Janz Tec Страницы: 20

Бренд: Magic Control Technology Страницы: 40

Бренд: Motorola Страницы: 143

PDX-089T-D5A-512

Бренд: Icop Страницы: 32

Бренд: Vecom Страницы: 153

Бренд: Barco Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды