HP Compaq dx7400 Series Скачать руководство пользователя страница 41

Страница: 41 / 69

Network status link light never flashes.

NOTE: The network status light is supposed to flash when there is network activity.

Cause

Solution

Network controller is not set up properly.

Check for the device status within Windows, such as Device
Manager for driver load and the Network Connections applet
within Windows for link status.

Network controller is disabled.

Run Computer Setup and enable network controller.

Enable the network controller in the operating system via
Device Manager.

Network driver is not properly loaded.

Reinstall network drivers.

System cannot autosense the network.

Disable auto-sensing capabilities and force the system into the
correct operating mode.

Diagnostics reports a failure.

Cause

Solution

The cable is not securely connected.

Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely
attached to the correct device.

The cable is attached to the incorrect connector.

Ensure that the cable is attached to the correct connector.

There is a problem with the cable or a device at the other end
of the cable.

Ensure that the cable and device at the other end are operating
correctly.

Network controller interrupt is shared with an expansion board. Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

The network controller is defective.

Contact an authorized service provider.

Diagnostics passes, but the computer does not communicate with the network.

Cause

Solution

Network drivers are not loaded, or driver parameters do not
match current configuration.

Make sure the network drivers are loaded and that the driver
parameters match the configuration of the network controller.

Make sure the correct network client and protocol is installed.

The network controller is not configured for this computer.

Select the

Network

icon in the

Control Panel

and configure

the network controller.

Network controller stopped working when an expansion board was added to the computer.

Cause

Solution

Network controller interrupt is shared with an expansion board. Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

The network controller requires drivers.

Verify that the drivers were not accidentally deleted when the
drivers for a new expansion board were installed.

The expansion board installed is a network card (NIC) and
conflicts with the embedded NIC.

Under the Computer Setup

Advanced

menu, change the

resource settings for the board.

Table 2-12

Solving Network Problems (continued)

ENWW

Solving Network Problems

Содержание Compaq dx7400 Series






































































Результаты поиска

Содержание Compaq dx7400 Series

Отзывы:

Похожие инструкции для Compaq dx7400 Series

Бренды по названию

Популярные бренды

HP Compaq dx7400 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание Compaq dx7400 Series

Отзывы:

Похожие инструкции для Compaq dx7400 Series

Бренды по названию

Популярные бренды