HP Compaq dx7400 Series Скачать руководство пользователя страница 37

Страница: 37 / 69

Mouse does not respond to movement or is too slow.

Cause

Solution

Mouse may need cleaning.

Remove the roller ball cover on the mouse and clean the
internal components.

Mouse may need repair.

See the Worldwide Limited Warranty for terms and conditions.

Wireless device error.

Check the software, if available, for device status.

Check/replace device batteries.

Reset receiver and mouse.

Computer is in

standby

mode.

Press the power button to resume from

standby

mode.

CAUTION:

When attempting to resume from

standby

mode,

do not hold down the power button for more than four seconds.
Otherwise, the computer will shut down and you will lose any
unsaved data.

Mouse will only move vertically, horizontally, or movement is jerky.

Cause

Solution

Mouse roller ball or the rotating encoder shafts that make
contact with the ball are dirty.

Remove roller ball cover from the bottom of the mouse and
clean the internal components with a mouse cleaning kit
available from most computer stores.

Table 2-10

Solving Mouse Problems (continued)

ENWW

Solving Keyboard and Mouse Problems

Содержание Compaq dx7400 Series






































































Результаты поиска

Содержание Compaq dx7400 Series

Отзывы:

Похожие инструкции для Compaq dx7400 Series

Бренды по названию

Популярные бренды

HP Compaq dx7400 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание Compaq dx7400 Series

Отзывы:

Похожие инструкции для Compaq dx7400 Series

Бренды по названию

Популярные бренды