manualshive.com logo in svg

HP C7745NB - SureStore DLT Tape Autoloader 1/9, Руководство пользователя

Поделиться
Скачать
HP C7745NB - SureStore DLT Tape Autoloader 1/9 Скачать руководство пользователя страница 57

Upgrading Firmware

Upgrading Firmware

Chapter 4

4-7

  U

pgr

adin

g F

irm

war

e 

  

Using a Firmware Upgrade Tape
(Drive Firmware Only)

1. Call your service representative to get the drive upgrade tape.

2. Ensure that you have removed all tapes from the drive.

If a tape is in the drive, use the front panel display to return the tape
to a storage slot. From the front panel, go to the following menus.

3. Load the firmware upgrade tape into an empty slot in the autoloader.

Note the slot number.

4. Use the following menu to perform the firmware upgrade:

5. From the

Upgrade Drive Firmware

menu, use the

[-]

or

[+]

key to select

the slot containing the firmware upgrade tape. Select

[OK]

.

6. Watch the upgrade status on the autoloader’s front panel. The tape

will return to the original storage slot when the procedure is
complete.

7. Remove the firmware upgrade tape from the autoloader.

8. Power-cycle the autoloader.

Operations ->

Drive and Tape Operations ->

Unload Tape from Drive

Main Menu ->

Administration ->

Upgrade Drive Firmware

Содержание C7745NB - SureStore DLT Tape Autoloader 1/9
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды