HP C7745NB - SureStore DLT Tape Autoloader 1/9 страница 54 Скачать руководство пользователя

Страница: 54 / 63

Upgrading Firmware

Upgrading Firmware

Chapter 4

4-4

You can also check your current firmware revisions from the remote
management card:

1. Enter the designated IP address into the web browser to launch the

Web-Based Library Administrator pages.

2. Select the

[Report]

tab.

3. Scroll down to the

Firmware Revisions

section of the page to view your

autoloader and drive firmware revisions.

NOTE

Ensure that your backup software does not “SCSI reserve” the autoloader,
as this can prevent a firmware download.

Using the Optional Remote Management Card
(Autoloader Firmware Only)

All autoloader component firmware, except drive firmware, can be easily
downloaded from the remote management card.

NOTE

The firmware files are available at www.hp.com/go/support, or contact
your support provier. These files must be loaded on the local host
computer before downloading firmware. First select your product, and
then select

Downloads & Drivers

1. Once the autoloader is configured for network access, enter the IP

address within your web browser to launch the web-based library
administrator pages. (See “Configuring the Remote Management
Card” on page 2-6.)

2. Select the

[Configuration]

tab from the main screen.

3. Select

[Firmware Download]

4. Enter the full path name for the download file, or use the

[Browse]

button to locate the file.

NOTE

The autoloader administrator password is required for this process. If the
password is not set, you will not be permitted to download firmware.

Содержание C7745NB - SureStore DLT Tape Autoloader 1/9
































































Результаты поиска

Содержание C7745NB - SureStore DLT Tape Autoloader 1/9

Отзывы:

Похожие инструкции для C7745NB - SureStore DLT Tape Autoloader 1/9

Бренды по названию

Популярные бренды

HP C7745NB - SureStore DLT Tape Autoloader 1/9, Руководство пользователя

Результаты поиска

Содержание C7745NB - SureStore DLT Tape Autoloader 1/9

Отзывы:

Похожие инструкции для C7745NB - SureStore DLT Tape Autoloader 1/9

Бренды по названию

Популярные бренды