manualshive.com logo in svg

HP C7745NB - SureStore DLT Tape Autoloader 1/9, Руководство пользователя

Поделиться
Скачать
HP C7745NB - SureStore DLT Tape Autoloader 1/9 Скачать руководство пользователя страница 56

Upgrading Firmware

Upgrading Firmware

Chapter 4

4-6

5. Connect the laptop SCSI interface to the device, using the

appropriate equipment and appropriate termination at the device
end.

6. Power-on the autoloader. Wait for the autoloader to complete the

power-on test and inventory check.

7. This step is for upgrading drive firmware only. If upgrading

autoloader firmware, continue to step 8.

Ensure that the drive is online (green LED is on and yellow LED is
off). If not, place it online through the front panel.

a. Enter the

Service

then the

Online Drive Repair

menus.

b. Select

[Put Drive Online]

.

The autoloader will automatically run a self-test when the drive has
been brought online. Wait until the self-test completes, and then scan
the SCSI bus or restart the diagnostics program.

NOTE

If the autoloader is in a partial availability state (solid amber LED) due
to a firmware mismatch, download new firmware.

8. Download the firmware to the device using the diagnostic tool.

9. Power-off the autoloader.

10. Disconnect the laptop and reconnect the autoloader to the host

system. Be sure to match the original cabling and termination setup.

11. Power cycle the autoloader.

12. Verify the device can be accessed from the host.

NOTE

When downloading drive firmware, you must power cycle the autoloader
for the download to be completed.

Содержание C7745NB - SureStore DLT Tape Autoloader 1/9
































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды