manualshive.com logo in svg

HP Aruba 6400 Series, Руководство по установке и началу работы

Поделиться
Скачать
HP Aruba 6400 Series Скачать руководство пользователя страница 66

Grounding the chassis

CAUTION: To protect the switch from hazards such as lightning shocks, interferences, and ESD

discharges, reliably ground it. The switch is grounded through the safety wire in the power

cords. If there is any doubt about the reliability of the grounding through the power mains,

Aruba recommends an independent grounding connection for the chassis. Note the location of

the grounding lug.

Figure 26: Grounding the chassis

1

1

Grounding lug

Make sure the resistance between the chassis and the ground is less than 1 ohm.

Prerequisites

Use a 6 AWG stranded grounding cable.

Procedure

1. Remove the grounding lug and two screws from the rear of the switch.
2. Crimp the grounding lug to a properly grounded 6 AWG stranded grounding cable.
3. Securely reattach the grounding lug to the switch with the two screws.

66

Aruba 6400 Switch Series Installation and Getting Started

Guide

Содержание Aruba 6400 Series








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды