
3-72
Chapter 3
Installation
Rebooting and Reconfiguring
In most cases, the "Protocol" field should be set to "Bell" or "CCITT". In the United
States, the protocol is usually "Bell." In Europe, the protocol is usually "CCITT."
The "Autodial Protocol" should match that of the modem.
5. If you need to change parameters, enter Y in response to the prompt. The system
displays a change menu:
6. An N response to the prompt in step 5 returns the CM> prompt.
7. From the system prompt CM>, enable remote access by a remote console command ER:
CM> ER
8. The system responds with the following display:
The "Remote CS" parameter enables the Copy Screen (CS) to be executed from the
remote console. The CS command copies a screen from the local console to the remote
console.
The "Mode" field determines whether only one remote access will be permitted (Single)
or many (Multiple).
Enter your change.
<CR> retains the current value.
Current bit rate is 9600 bits/sec.
Select the new bit rate.
(0=300, 1=1200, 2=2400, 3=4800, 4=9600, 5=19200): 2
Current Protocol is CCITT.
Select the new protocol.
(0=CCITT, 1=Bell, 2=CCITT_BIS): 1
Current Autodial Protocol is V25.BIS.
Select the new protocol.
(0=V25.bis, 1=Hayes): 1
Current System identification: System_name
New system identification (limited to 1 to 23 displayable characters
or space for none): (New_system_name)
New configuration (takes effect at next remote connection):
Bit rate:
2400 bits/sec
Protocol:
Bell
Autodial Protocol:
Hayes
System identification:
System_name
Current remote console access configuration:
Remote CS:
Enabled
Mode:
Multiple
Password:
(current password)
Password faults:
03
Do you wish to change the configuration? (Y/N):
Содержание 3000 99x Family
