manualshive.com logo in svg

HP 268 Pro G1 MT, Руководство по техническому обслуживанию и ремонту

Поделиться
Скачать
HP 268 Pro G1 MT Скачать руководство пользователя страница 49

Poor performance.

Cause

Solution

Virus resident on the hard drive.

Run virus protection program.

Too many applications running.

1.

Close unnecessary applications to free up memory.

2.

Add more memory.

3.

Some applications run in the background and can be closed by 
right-clicking on their corresponding icons in the task tray. To 
prevent these applications from launching at startup:

a.

Type 

msconfig

 in the taskbar search box, and then 

select msconfig.

b.

On the Startup tab of the System Configuration Utility, 
click Open Task Manager.

c.

Select applications that you do not want to launch 
automatically, and the click Disable.

Some software applications, especially games, are stressful on the 
graphics subsystem.

1.

Lower the display resolution for the current application or 
consult the documentation that came with the application for 
suggestions on how to improve performance by adjusting 
parameters in the application.

2.

Add more memory.

3.

Upgrade the graphics solution.

Cause unknown.

Restart the computer.

Computer powered off automatically and the oower light flashes red four times and then white two times.

Cause

Solution

Processor thermal protection activated:

A fan might be blocked or not turning.

OR

The heat sink is not properly attached to the processor.

1.

Ensure that the computer air vents are not blocked and the 
processor cooling fan is running.

2.

Open the access panel, press the power button, and see if the 
processor fan (or other system fan) spins. If the fan does not 
spin, make sure the fan cable is plugged onto the system 
board header.

3.

If fan a plugged in and not spinning, replace it.

System does not power on and the lights on the front of the computer are not flashing.

Cause

Solution

System unable to power on.

Press and hold the power button for less than 4 seconds. If the hard 
drive light turns white, then:

1.

If equipped with a voltage selector, check that the voltage 
selector (located on the rear of the power supply) is set to the 
appropriate voltage. Proper voltage setting depends on your 
region.

2.

Remove the expansion cards one at a time until the 5V_aux 
light on the system board turns on.

3.

Replace the system board.

Solving general problems

41

Содержание 268 Pro G1 MT











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды