Hospira LifeCare XL Series Скачать руководство пользователя | Manualshive

Страница: 92 / 278

background image

7.2

REPLACEMENT PROCEDURES

Technical Service Manual

7 - 13

430-00587-008 (Rev. 2/05)

CONTROL KNOB, KNOB DETENT, WASHER, GASKET, SNAP
RETAINER, AND DETENT RING REPLACEMENT

Recommended tools for this procedure are a small flat blade screwdriver, a medium size
flat blade screwdriver, a No. 2 Phillips screwdriver, and long needle nose pliers.

The replacement parts for this procedure are:

Retainer, Snap, Knob
Knob, Control
Detent, Knob
Washer, Knob
Gasket, Knob
Ring, Detent
Shim
Magnet

CAUTION:

Use proper ESD grounding techniques when handling components.

Wear an antistatic wrist strap and use an ESD-protected workstation. Store the PWA
in an antistatic bag before placing it on any surface.

To replace the control knob, knob detent, washer, gasket, detent ring, and snap retainer,
refer to

, then proceed as follows:

1. Separate the front enclosure assembly and rear enclosure assembly as described

Section 7.2.5

2. Remove the display PWA as described in

Section 7.2.7.1

.

3. Remove the front panel keys as described in

Section 7.2.7.2

4. Using long needle nose pliers, carefully remove the snap retainer.

5. Remove the control knob, knob detent, shim, washer, gasket, and detent ring.

6. Inspect the magnet on the knob detent. If the magnet appears damaged, carefully

remove it using the small flat blade screwdriver. Install the replacement, assuring
that the dot on the magnet is facing up.

7. Install the replacement control knob, washer, and gasket.

- Fit the gasket into the circular recess on the front side of the front enclosure.

- Install the washer on the control knob.

- Install the shim on the control knob.

- Place the control knob through the hole in the front enclosure.

- Turn the control knob to OFF/CHARGE.

8. Place the front enclosure assembly face down. Place the detent ring on the four

pins, centered on the control knob. Assure that the raised bumps on the detent
ring are facing up.

9. Using the snap retainer, secure the knob detent on the control knob retainer clips

and splines. Press the snap retainer firmly until it is secure.



Note:

When the control knob is at OFF/CHARGE, the knob detent is

positioned on the detent ring as shown in

10. Verify that the control knob rotates fully.

11. Reassemble the device in the exact reverse order of disassembly.

«
...
90
91
92
93
94
...
»

Содержание LifeCare XL Series























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LifeCare XL Series

Бренд: Panasonic Страницы: 180

Бренд: B&G Страницы: 3

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Бренд: Kärcher Страницы: 88

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Бренд: Tar River Страницы: 61

LUXOMAT net PBM-KNX-DX-4W

Бренд: B.E.G. Страницы: 16

Бренд: Ebyte Страницы: 7

Бренд: v.link Страницы: 20

Бренд: BCP Страницы: 8

Бренд: Seiler Страницы: 7

Westeel EasyFlow2 100 Series

Бренд: AGI Страницы: 74

PRO-PORTAL 40010021

Бренд: PROLUMIA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды