Hospira LifeCare XL Series Скачать руководство пользователя | Manualshive

Страница: 98 / 278

background image

7.2

REPLACEMENT PROCEDURES

Technical Service Manual

7 - 19

430-00587-008 (Rev. 2/05)

VELCRO RETAINER STRAP REPLACEMENT

No tools are required for this procedure.

The replacement part for this procedure is:

Strap, Velcro, 1.75 in x 10 in, Black

To replace the Velcro retainer strap, remove the strap from the power cord and install the
replacement

(see Figure 7-7)

Replacement of the Velcro retainer strap is a routine maintenance procedure and no
verification procedure is normally required. However, if the infusion system may have been
damaged during the Velcro retainer strap replacement, perform the PVT in

AC (MAINS) POWER CORD AND STRAIN RELIEF BUSHING
REPLACEMENT

Recommended tools for this procedure are a medium size flat blade screwdriver,
a 1/4 inch nutdriver, and pliers.

The replacement parts for this procedure are:

Cordset, AC Power, Hospital Grade
Strain Relief, Nylon, Black
Nut, 6-32, KEP, with Washer
Washer, Flat, #6
Screw, 6-32 x 3/4, Hex Head, Slotted, w/Washer (XL)
Screw, 6-32 x 1, Hex Head, Slotted, w/Washer (XLM)

CAUTION:

Use proper ESD grounding techniques when handling components.

Wear an antistatic wrist strap and use an ESD-protected workstation. Store the PWA
in an antistatic bag before placing it on any surface.

To replace the AC (mains) power cord, and strain relief bushing, refer to

Figure 7-8, AC

Power Cord (115 VAC - Plum XL)

Figure 7-9, AC Power Cord (115 VAC - Plum XLM)

proceed as follows:

1. Separate the front enclosure assembly and rear enclosure assembly as described

Section 7.2.5

2. Using a 1/4 inch nutdriver, remove the two hex head nuts from the hex head ground

screw.

3. Disconnect the green ground wire from the ground screw.

4. Disconnect the AC (mains) power cord wire from J16

(see Table 7-1, Wire Color

5. Disconnect the AC (mains) power cord wire from J17

(see Table 7-1)

6. Use the pliers to remove the strain relief bushing.

7. Pull the AC (mains) power cord through the mounting hole in the rear enclosure

assembly.

8. Install the replacement AC (mains) power cord in the exact reverse order of removal.

«
...
96
97
98
99
100
...
»

Содержание LifeCare XL Series























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LifeCare XL Series

Бренд: Yamaha Страницы: 50

Бренд: A&D Страницы: 30

Бренд: TC Electronic Страницы: 14

Бренд: Access Страницы: 7

Бренд: Teac Страницы: 44

Бренд: Te Pari Страницы: 6

Бренд: VADDIO Страницы: 58

Бренд: Guyatone Страницы: 2

Бренд: IBC Страницы: 4

Бренд: Garmin Страницы: 2

Бренд: Ganter Norm Страницы: 20

Wallach UltraFreeze

Бренд: Cooper Surgical Страницы: 4

Бренд: HYDRA-RIB Страницы: 25

Бренд: Osprey Medical Страницы: 49

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренд: Psiber Страницы: 16

SonicShield I Micro

Бренд: CMS Marine Страницы: 15

Бренд: Dean Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды