Hospira LifeCare XL Series Скачать руководство пользователя

Страница: 57 / 278

SECTION 5 MAINTENANCE AND SERVICE TESTS

430-00587-008 (Rev. 2/05)

5 - 12

Plum XL Series

5.2.14

DELIVERY ACCURACY TEST



Note:

Accuracy testing is for informational purposes only, and is not to be used as

a re-release test. If there is any concern as to infusion system accuracy, return the
infusion system to Hospira Technical Support Operations.

CAUTION:

Do not remove the protective cover from the butterfly needle.

To perform the delivery accuracy test, proceed as follows:

1. Attach an 18-gauge cannula, or a 21-gauge needle, to the distal end of the tubing.

Verify the fluid container is 18 to 24 inches (46 to 60 cm) above the cassette pumping
chamber. Verify all lines are unclamped.

2. Prime the tubing. Verify no air is in the tubing. Place cannula or needle in a 25 mL

graduated cylinder.

3. Turn the control knob to SET RATE and set the primary rate to 400 mL/hr.

4. Press [PRI/SEC] to display SECONDARY and set the secondary rate to 400 mL/hr.

5. Turn the control knob to SET VTBI and press [PRI/SEC] to display PRIMARY.

6. Set the primary volume to 10 mL.

7. Press [PRI/SEC] to display SECONDARY and set the secondary volume to 10 mL.

8. Turn the control knob to CLEAR VOL to clear previous value. Verify four beeps

sound.

9. Assure the graduated cylinder is dry.

10. Turn the control knob to RUN to start pumping fluid. Verify volume delivered is

20 ± 1 mL. Verify that after the VTBI is complete, the infusion system changes to
KVO mode at a rate of 1 mL/hr.

11. Turn the control knob to OFF/CHARGE.

12. Clamp both lines. Remove the distal tubing. Remove the cassette from the infusion

system.

5.2.15

EMPTY CONTAINER/AIR-IN-LINE ALARM TEST

To perform the empty container/air-in-line alarm test, proceed as follows:

1. Install the special cassette marked EMPTY in the infusion system. Confirm the

special cassette proximal bubble sensor tips are removed

(see Figure 5-6, Special

Cassettes with Bubble Sensor Tips Removed)

2. Turn the control knob to SET VTBI.

3. Set the volume to 100 mL.

4. Turn the control knob to RUN to start pumping. Verify that within three pumping

cycles the audible alarm sounds and the AIR-IN-LINE and BACKPRIMING legends
display.

5. Turn the control knob to HOLD/RESET.

6. Open the cassette door and remove the cassette.

7. Install the special cassette marked AIR in the infusion system. Confirm the special

cassette distal bubble sensor tips are removed

(see Figure 5-6)

8. Turn the control knob to RUN to start pumping. Verify that within three pumping

cycles the alarm sounds and the AIR-IN-LINE legend displays.

Содержание LifeCare XL Series























































































































































































































































































Результаты поиска

Содержание LifeCare XL Series

Отзывы:

Похожие инструкции для LifeCare XL Series

Бренды по названию

Популярные бренды

Hospira LifeCare XL Series, Техническое и сервисное руководство

Результаты поиска

Содержание LifeCare XL Series

Отзывы:

Похожие инструкции для LifeCare XL Series

Бренды по названию

Популярные бренды