Hoshizaki Serenity KMS-2000MLJ Скачать руководство пользователя | Manualshive

Страница: 29 / 36

background image

29

Fig. 18

Fig. 19

13) Replace the splash curtain, front frame, and insulation panel in their correct positions

and secure with the thumbscrews.

14) Seal the outer perimeter of the front frame to the icemaker and dispenser unit/storage

bin with RTV-748 sealant (provided) or equivalent. See Fig. 19. Make sure the front
frame sealant meets the previously applied perimeter sealant and that there are no
gaps.

15) Move the control switch to the "ICE" position.
16) Replace the front panel in its correct position.
17) Turn on the power supply to start the automatic icemaking process.

Pump Suction Hose

Drain Pipe

Water Tank Drain Hose

Float Connection Hose

Splash Curtain

Evaporator Case Wall

Water Tank

Front Frame

Bin Control

Insulation Panel

Front Panel

Front Frame

Seal the Front Frame Outer Perimeter with RTV-748 Sealant

or Equivalent. Make sure the front frame sealant meets the

previously applied perimeter sealant and that there are no gaps.

«
...
27
28
29
30
31
...
»

Содержание Serenity KMS-2000MLJ





































Отзывы:

Нет отзывов

Похожие инструкции для Serenity KMS-2000MLJ

Бренд: La Spaziale Страницы: 104

Бренд: Acopino Страницы: 42

Бренд: san ignacio Страницы: 28

Бренд: U-Line Страницы: 44

Бренд: Lagrange Страницы: 60

Mini-Cappuccino

Бренд: Newco Страницы: 24

Бренд: Melitta Страницы: 57

Бренд: SEWOO Страницы: 18

Бренд: Faema Страницы: 100

Бренд: Omcan Страницы: 16

8 7121 8405 6446

Бренд: Bestron Страницы: 40

Бренд: Russell Hobbs Страницы: 8

Бренд: Estella Страницы: 15

Saeco Poemia HD8323/98

Бренд: Saeco Страницы: 3

Бренд: Salton Страницы: 8

Бренд: DeLonghi Страницы: 14

Бренд: Saeco Страницы: 38

Бренд: Ice-O-Matic Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды