Hoshizaki Serenity KMS-2000MLJ страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 36

background image

33

B. Maintenance

This icemaker must be maintained individually, referring to the instruction manual and
labels provided with the icemaker.

WARNING

•

Only qualified service technicians should service this icemaker.

•

Move the control switch to the "OFF" position and turn off the power supply to

the remote condensing unit before servicing. Place the icemaker disconnect
(if applicable) in the off position. Lockout/Tagout to prevent the power supply from
being turned back on inadvertently.

1. Stainless Steel Exterior

To prevent corrosion, wipe the exterior occasionally with a clean, soft cloth. Use a damp
cloth containing a neutral cleaner to wipe off oil or dirt buildup.

2. Storage Bin Scoop

• Wash your hands before removing ice from the storage bin. Use the plastic scoop

provided (storage bin accessory).

• Clean the scoop using a neutral cleaner. Rinse thoroughly after cleaning.

3. Dispenser Unit/Storage Bin

• The dispenser unit/storage bin is for ice use only. Do not store anything else in the

dispenser unit/storage bin.

• Clean the dispenser unit/storage bin liner using a neutral cleaner. Rinse thoroughly after

cleaning.

4. Condenser

Check the condenser once a year, and clean the coil if required by using a brush or
vacuum cleaner. More frequent cleaning may be required depending on location.

«
...
31
32
33
34
35
...
»

Содержание Serenity KMS-2000MLJ





































Отзывы:

Нет отзывов

Похожие инструкции для Serenity KMS-2000MLJ

Бренд: OBH Nordica Страницы: 24

Бренд: La Marzocco Страницы: 55

Бренд: La Marzocco Страницы: 3

Бренд: La Spaziale Страницы: 12

Бренд: La Spaziale Страницы: 30

Бренд: La Spaziale Страницы: 22

Бренд: La Marzocco Страницы: 18

Бренд: La Marzocco Страницы: 32

Бренд: La Marzocco Страницы: 16

Бренд: La Marzocco Страницы: 2

Бренд: La Marzocco Страницы: 116

Бренд: La Marzocco Страницы: 2

Бренд: La Spaziale Страницы: 64

Бренд: Dash Страницы: 32

Anytron Any-002

Бренд: Valloy Incorporation Страницы: 68

Бренд: Officine Gullo Страницы: 12

SCLUSIVO DCF210TTC

Бренд: DeLonghi Страницы: 1

Бренд: Ugolini Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды