manualshive.com logo in svg

Hoshizaki Serenity KMS-2000MLJ, Инструкция по эксплуатации

Поделиться
Скачать
Hoshizaki Serenity KMS-2000MLJ Скачать руководство пользователя страница 15

15

2. Water Tank Removal

1) Remove the front frame and splash curtain. See Fig. 7.
2) Disconnect the pump suction hose, drain pipe, and float connection hose at the 

evaporator case wall. Disconnect the water tank drain hose from the bottom of the 
water tank. Although the water tank can be removed at this point, do not remove it yet 
because the bin control is taped inside the water tank.

NOTICE

The bin control cable is routed through the back of the icemaker. If care is not taken 
when removing the water tank, the bin control cable could be severed.

Pump Suction Hose

Drain Pipe

Water Tank Drain Hose

Float Connection Hose

Splash Curtain

Fig. 7

Evaporator Case Wall

Water Tank

Front Frame

3) Pull out the water tank only as far as shown in Fig. 8.
4) Remove the cube guide, then remove the bin control assembly.
5) 

Being careful not to pull the bin control cable,

 remove the water tank completely 

from the icemaker.

6) Remove the remaining pieces of tape from the water tank and leave the water tank out 

of the icemaker for now.

Fig. 8

Bin Control Cable

Cube Guide

Содержание Serenity KMS-2000MLJ





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды