Hoshizaki Serenity KMS-2000MLJ страница 30 Скачать руководство пользователя

Страница: 30 / 36

III. Cleaning and Maintenance

This icemaker must be cleaned and maintained in accordance with the instruction
manual and labels provided with the icemaker. Consult with your local Hoshizaki Certified
Service Representative about cleaning and maintenance service.

WARNING

• Only qualified service technicians should service this icemaker.
•

CHOKING HAZARD:

Ensure all components, fasteners, and thumbscrews are

securely in place after any cleaning or maintenance is done to the unit. Make sure
that none have fallen into the dispenser unit/storage bin.

NOTICE

The dispenser unit/storage bin is for ice use only. Do not store anything else in the
dispenser unit/storage bin.

A. Cleaning and Sanitizing Instructions

This icemaker must be cleaned and sanitized at least once a year. More frequent
cleaning and sanitizing may be required in some water conditions.

WARNING

• To prevent injury to individuals and damage to the icemaker, do not use ammonia

type cleaners.

• Carefully follow any instructions provided with the bottles of cleaning and

sanitizing solution.

• Always wear liquid-proof gloves and goggles to prevent the cleaning and sanitizing

solutions from coming into contact with skin or eyes.

NOTICE

To prevent damage to the water pump seal, do not operate the icemaker with the
control switch in the "SERVICE" position when the water tank is empty.

Splash Curtain

Float Switch

Insulation Panel

Front Panel

Fig. 20

Содержание Serenity KMS-2000MLJ





































Результаты поиска

Содержание Serenity KMS-2000MLJ

Отзывы:

Похожие инструкции для Serenity KMS-2000MLJ

Бренды по названию

Популярные бренды

Hoshizaki Serenity KMS-2000MLJ, Инструкция по эксплуатации

Результаты поиска

Содержание Serenity KMS-2000MLJ

Отзывы:

Похожие инструкции для Serenity KMS-2000MLJ

Бренды по названию

Популярные бренды