Hoshizaki RF28A Скачать руководство пользователя страница 30

Страница: 30 / 47

Problem

Possible Cause

Remedy

d) Compressor Relay

1. Defective; contacts

welded.

1. Replace.

e) Control Board

1. Defective.

1. Replace.

[8] Evaporator does

not defrost
completely.

a) Defrost Thermistor

1. Defective.

1. Check and replace.

b) Defrost

1. Not enough defrosts

occurring per day.
Operation in humid
conditions.

1. Factory default is once

every 6 hours. If coil is
frosting too much, can
shorten defrost interval.

c) Defrost Heaters

1. Defective.

1. Replace heaters.

d) Safety Defrost

Thermostat

1. Defective, turning off

heaters prematurely,
or open.

1. Replace safety defrost

thermostat.

e) Defrost Heater Thermal

Fuse

1. Blown.

1. Determine why fuse blew.

Replace fuse.

f) Evaporator Shroud

Heater

1. Defective and causing

freeze-up of drain to
drain tank.

1. Replace evaporator

shroud.

[9] Defrost cycle

lasts too long.

a) Defrost Thermistor

1. Defective.

1. Replace.

b) Control Board

1. Defective.

1. Replace.

c) Defrost

1. Not enough defrosts

occurring per day.
Operation in humid
conditions.

1. Factory default is once

every 6 hours. If coil is
frosting too much, can
shorten defrost interval.

d) Defrost Heaters

1. Defective.

1. Replace heaters.

e) Safety Defrost

Thermostat

1. Defective, turning off

heaters prematurely,
or open.

1. Replace safety defrost

thermostat.

[10]Condensate

water overﬂow.

a) Cabinet Contents

1. Loading of large

volumes of warm,
moist, uncovered
product.

1. Cover product with plastic

wrap.

b) Location of Unit

1. Unit located near high

humidity source such
as fryer, steamer, etc.

1. Relocate.

c) Seals

1. Poor sealing around

evaporator, door
gaskets.

1. Adjust or replace.

d) Environment

1. Extreme environment

and door-opening
conditions.

1. Adjust conditions.

e) Primary Drain Tank

Thermostat

1. Defective, turning off

heater prematurely, or
open.

1. Replace primary drain

tank thermostat.

f) Safety Drain Tank

Thermostat

1. Defective, turning off

heater prematurely, or
open.

1. Replace safety drain tank

thermostat.

g) Drain Tank Thermal

Fuse

1. Blown.

1. Determine why fuse blew.

Replace fuse.

h) Drain Tank Heater

1. Defective.

1. Replace heater.

Содержание RF28A
















































Результаты поиска

Содержание RF28A

Отзывы:

Похожие инструкции для RF28A

Бренды по названию

Популярные бренды

Hoshizaki RF28A, Руководство по обслуживанию

Результаты поиска

Содержание RF28A

Отзывы:

Похожие инструкции для RF28A

Бренды по названию

Популярные бренды